Melden Sie sich zuerst an, um alle Funktionen optimal nutzen zu können!

Influence of Viscosity-interface Modifier Interactions on Performance and Processability of Rice Hull PE Composites (Englisch)

In: INTERNATIONAL POLYMER PROCESSING   ;  21 ,  5  ;  504-508  ;  2006
  • ISSN:
    0930-777X
  • Aufsatz (Zeitschrift)  /  Print

Exportieren, teilen und zitieren

© Metadata Copyright the British Library Board and other contributors. All rights reserved.

Inhaltsverzeichnis – Band 21, Ausgabe 5

Zeige alle Jahrgänge und Ausgaben

Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.

436
Rapid Communications - A Novel High Flow Rate Pin for Water-assisted Injection Molding of Plastic Parts with a More Uniform Residual Wall Thickness Distribution
Liu, S.-J. et al. | 2006
436
A Novel High Flow Rate Pin for Water-assisted Injection Molding of Plastic Parts with a More Uniform Residual Wall Thickness Distribution
Liu, S.-J. / Wu, Y.-C. et al. | 2022
440
Structure Property Relationships in PA 6 and PP Copolymers Blended by Single and Twin Screw Extrusion
Correa, C. A. / Carvalho, C. L. / Bezzan, A. L. / Razzino, C. A. / HageJr., E. et al. | 2022
449
Stretchability and Properties of Biaxially Oriented Polypropylene Film
Kanai, T. / Uehara, H. / Sakauchi, K. / Yamada, T. et al. | 2022
457
Dynamic Mold Surface Temperature Control Using Induction and Heater Heating Combined with Coolant Cooling
Chen, S. C. / Jong, W. R. / Chang, J. A. / Chang, Y. J. et al. | 2022
464
Visualization of Melt-Flow Behavior Inside the Runner in Ultra High Speed Injection Molding
Hasegawa, S. / Yokoi, H. et al. | 2022
473
Effects of Cavity Conditions on Transcription Molding of Microscale Prism Patterns Using Ultra-High-Speed Injection Molding
Han, X. / Yokoi, H. / Takahashi, T. et al. | 2022
480
Effect of Melt and Mold Temperature on Fiber Orientation during Flow in Injection Molding of Reinforced Plastics
Shokri, P. / Bhatnagar, N. et al. | 2022
487
Polymer/Layered Silicate Nano-composites
Okamoto, M. et al. | 2022
497
Paste Extrusion of Polytetrafluoroethylene: Temperature, Blending and Processing Aid Effects
Ochoa, I. / Hatzikiriakos, S. G. / Mitsoulis, E. et al. | 2022
504
Influence of Viscosity-interface Modifier Interactions on Performance and Processability of Rice Hull PE Composites
Dixit, N. / Sain, M. / Kortschott, M. T. / Gulati, D. et al. | 2022
509
Single and Multi Objective Optimization for Injection Molding Using Numerical Simulation with Surrogate Models and Genetic Algorithms
Zhou, J. / Turng, L.-S. / Kramschuster, A. et al. | 2022
521
A Process Classification Number for the Solidification of Crystallizing Materials
Janeschitz-Kriegl, H. / Eder, G. / Ratajski, E. et al. | 2022
527
Effect of Aerodynamics on Film Blowing Process
Zhang, Z. / Lafleur, P. G. / Bertrand, F. et al. | 2022
535
Book Review: Structure and Rheology of Molten Polymer
Mackley, M. et al. | 2006
536
Analysis of Necking Deformation Behavior in High-Speed In-line Drawing Process of PET by On-line Diameter and Velocity Measurements
Hahm, W.-G. / Ito, H. / Kikutani, T. et al. | 2022
544
PPS News
| 2022
545
Seikei-Kakou Abstracts
| 2022
546
PPS Membership Application-Impressum
| 2006
547
Yearly Index 2006
| 2006
i
Contents
| 2022

Exportieren, teilen und zitieren

Feedback