Power generation using parabolic dish CSP technology (Englisch)

in AIP Conference Proceedings ; 2204 , 1 ; 10
AIP Conference Proceedings

Solar light has been harnessed using ever evolving photovoltaic technology. But concentrated solar heat is more efficient as well as produces dispatchable power. This project is an embarkation for utilization of concentrated solar heat energy at domestic as well as industrial usage. Parabolic dish has been used for the concentration of solar power and open cycle is used for energy conversion from concentrated heat to electricity. The maximum temperature of 960 degrees Celsius is obtained. The custom designed storage cum receiver is used with our own fabricated turbine and it is to be connected to a 12 V dc generator for production of electricity. The receiver of capacity 800 cc of water is designed along with the reaction turbine rotating at speed of 600 rpm producing 220 mA of current and running a 5 V motor where a fan is fitted. The efficiency is found to be quite less but it is a new field of research thus it is an initiative for new researchers to contribute in further studies. The methods applied to ensure maximum utilization are proper setup of parabolic dish as well as the receiver. Similarly, design of receiver and turbine as well as their compatibility is important for efficient power generation. Also, the pressure of steam can also be increased by adding Nano fluids, i.e. fluid suspensions of nanometer-sized solid particles and fibers like carbon Nano tubes which can increase the efficiency of this process.

Wie erhalte ich diesen Titel?
Download
Kommerziell Vergütung an den Verlag: 24,35 € Grundgebühr: 4,00 € Gesamtpreis: 28,35 €
Akademisch Vergütung an den Verlag: 16,23 € Grundgebühr: 2,00 € Gesamtpreis: 18,23 €

Dokumentinformationen


Inhaltsverzeichnis – Band 2204, Ausgabe 1

Zeige alle Jahrgänge und Ausgaben

Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Nachweisen der enthaltenen Aufsätze. Die Anzeige der Jahrgänge kann aufgrund fehlender Aufsatznachweise unvollständig oder lückenhaft sein, obwohl die Zeitschrift komplett in der TIB verfügbar ist.

Analytical study on the seismic behavior of two adjacent buildings connected by viscous dampers
Khan, Shadab / Kumar, C. L. Mahesh / Shwetha, K. G. | 2020
A study on index properties of kaolinite and bentonite sand mixtures
Jyothi, D. N. / Prasanna, H. S. / Vishwanath, Chethan | 2020
Analysis of water quality parameters of groundwater near Ranebennur Industrial Area, Haveri district, Karnataka, India
Vijaya Kumar, H. / Patil, Nagraj. S. / Prabhu, Nanjundi | 2020
An experimental investigation of grit size effect over a smooth circular cylinder
Bharatbhai, Babaria Harit / Ramakrishna, J. / Tahasildar, Firoz H. / Somashekar, V. | 2020
The effect of planetary milling conditions on tungsten-carbide (WC) particle size reduction and sintered properties
Aithal, Kiran / Manjunath, H. N. / Babu, N. Ramesh / Kumar, Praveen / Atreya | 2020
Computational studies on laminar flow in micro-channel heat sinks for electronic cooling applications
Manjunath, H. N. / Naveen, K. S. / Babu, N. Ramesh / Aithal, Kiran / Veda, S. N. | 2020
Finite element formulation of conjugate double diffusion in porous annulus
Baig, Maughal Ahmed Ali / Azeem / Ahmed, N. J. Salman / Kamangar, Sarfaraz / Khan, T. M. Yunus / Badruddin, Irfan Anjum / Reddy, Avala Raji / Khaleed, H. M. T. | 2020
Optimisation of machining parameters for end milling of maraging steel MDN 250 using TiAlSiN and TiSiN coated WC-Co inserts
Varghese, Vinay / Jagmalpuria, Abhishek / Badiger, Pradeep V. / R., Ramesh M. | 2020
Issues on planning of solid waste management scheme through evaluation in integrated data information system
Rao, Kumar R. / Sreekeshava, K. S. / Dharek, Manish S. / Sunagar, Prashanth | 2020
Physico chemical analysis of intrusions in Bellandur lake
Monesh, M. / Karthik, N. / Kumar, Dilip / Bharath, V. / Korishetti, Naveen / Vidyavathi, N. | 2020
Experimental investigation on axially loaded alkali activated slag concrete (AASC) and traditionally vibrated concrete (TVC) square
Srinivasulu, Surapuraju / Wali, Laxmiputra S. / R., Mourgouane | 2020
Influence of erodent size, impingement angle and fillers on solid particle erosion wear behaviour of carbon fiber reinforced epoxy composite
Prashanth, N. | 2020
Finite element analysis of bonded patch repair of a panel with multiple cracks
Srilakshmi, R. / Rao, M. Vedanth / Kumar, R. Sanjay | 2020
Implementation of Taguchi method and ANNOVA for optimization of process parameter in improving the surface roughness of the products in injection moulding operation
Kumar, Satyam / Ray, Gaurav Kumar / Maharjan, Deep / Adoni, Dadapeer / Shetty, P. Balachandra / Yadav, Shiv Pratap Singh | 2020
Experimental study on Bamboo as a reinforcing material in concrete
Sutharsan, R. / Ramprasanna, S. R. / Gnanappa, S. Basil / Ganesh, A. Chithambar | 2020
Evolutionary optimisation for optimising process parameters in vacuum carburising
Mallick, Priyabrata / R. H., Shashanka / C. G., Shivaprasad | 2020
Static aero-elastic analysis of wind tunnel test model in transonic flow
Siddalingappa, P. K. / Dharmendra, A. P. / Hosur, Santosh / Manvi, Prashant | 2020
Simulation of backward facing step flow using OpenFOAM®
Satheesh Kumar, Aravind / Singh, Anugya / Thiagarajan, Kannan Budda | 2020
Rural development studies under Unnath Bharath Abhiyan a case study of Chikkapalnahalli and Tannenahalli village
Veerappadevaru, G. / Sharma, H. D. / Manu, H. M. / Mallikarjuna, S. D. / Rashmi, B. V. / Kavya, D. | 2020
Evaluation of level of service at few signalized intersections using Indian Highway Capacity Manual (Indo-HCM, 2018)
Savitha, B. G. / Satyamurthy, R. / Jagadeesh, H. S. / Sathish, H. S. / Sundararajan, T. | 2020
The screening efficiency of linear vibrating screen - An experimental investigation
Kumar, S. Bharath / Vardhan, Harsha / Raj, M. Govinda / Kaza, Marutiram / Sah, Rameshwar / Harish, H. | 2020
SEM characterization of 3D printed ABS tensile specimens developed by fused deposition modelling
Prasad, Kaushik V. / Adarsha, H. / Pattnaik, Ashutosh / Shashank, B. / Kiran, P. Sri Sai / Mallikarjuna, Mitai / Sandeep, B. | 2020
Power generation using parabolic dish CSP technology
Pathak, Rabi / C., Pramod K. / Madhusudhan / L., Harish Kumar / Giri, Nabin / Uprety, Sujan | 2020
Impact of sized abrader and normal load on deformation morphology of EN 24 steel subjected to abrasion
Hemaraju | 2020
A case study on project performance of railway underpass construction project in Jaipur, India
Ojha, Avinash / Chouhan, Vineet / Gupta, Lokesh / Goswami, Shubham | 2020
Precipitation overflow demonstration and rainfall-runoff modeling by regression analysis: A case study
Surendra, H. J. / Junaid, Mohammed Qaisar / Prajeesh, P. / Lalith Kumar, S. / Hussain Malik, Junaid | 2020
CFD simulation of turbulent flow around multi-element airfoil
Gupta, Sonali / Naveen, R. / Prathik, B. V. / Spurthy, S. | 2020
Study on effect of semi-circular dimple on aerodynamic characteristics of NACA 2412 airfoil
Sowmyashree, Y. / Aishwarya, D. I. P. / Spurthy, S. / Sah, Roshan / Pratik, B. V. / Srikanth, H. V. / Suthan, R. | 2020
The study of microstructure and wear behaviour of titanium nitride reinforced aluminium composites
Mahesh, L. / Reddy, J. Sudheer / Jagadeesh, L. R. / Vinyas, M. | 2020
Influence of Ti coated tools on process parameters in turning process of MDN431
Badiger, Pradeep V. / Desai, Vijay / Ramesh, M. R. / Vinyas, M. / Santhosh, C. M. / Prajwala, B. K. / Raveendra, L. | 2020
Slurry erosive study and optimization of material and process parameters of single and hybrid matrix flexible composites using Taguchi approach
Mahesh, Vishwas / Joladarashi, Sharnappa / Kulkarni, Satyabodh M. | 2020
Design and analysis of composite panel with curved stiffeners for aircraft fuselage application
Aditya, A. R. / Babu, N. C. Mahendra | 2020
MWD technique to estimate the uniaxial compressive strength of rocks
Lakshminarayana, C. R. / Tripathi, Anup Kumar / Pal, Samir Kumar | 2020
A Bayesian approach to predict the structural responses of FGM plates with uncertain parameters
Loja, M. A. R. / Carvalho, A. / Neto, J. P. / Silva, T. A. N. / Vinyas, M. | 2020
Study on effect of surface modification on aerodynamic characteristics of Eppler 387 airfoil
Spurthy, S. / Sumukha, G. D. / Prathik, B. V. / Naveen, R. / Srikanth, H. V. / Sridhar, K. | 2020
Optimization of the surface quality in milling machine using PVC composite plate
Ahirwar, Yashwant / Soni, Hargovind / Mashinini, P. M. / Dewangan, Shailesh | 2020
Development & characterization of composite coatings on A-36 steel using HVOF technique
Adarsha, H. / Pattanaik, A. / Chaturvedi, A. / Bhat, S. | 2020
Dynamic performance of laminated composite plates with a circular hole
Kallannavar, Vinayak / Umatar, Sagar / Kattimani, S. | 2020
The effect of reinforcements on mechanical properties of A7005 hybrid MMCs
Kumar, S. Praveen / Shantharaja, M. / Vinyas, M. | 2020
Experimental studies to demonstrate the influence of fibres on shear strength of GPC adopting push-off specimens
Kumar, N. R. Harish / Kumar, K. Anil / Ganesh, Bharathi / Prabhakara, R. | 2020
Stagewise performance evaluation of common effluent treatment plant at Koparkairane, Navi Mumbai
Selvam, Shanthi P. / Topkar, V. M. | 2020
Comparison between artificial neural network and SPSS to predict vehicle emission
Ramprasanna, S. R. / Ganesh, A. Chithambar / Basil Gnanappa, S. / Sutharsan, R. | 2020
Assessment of groundwater quality by integration of water quality index and GIS techniques
Nandeesha / Khandagale, Vishal. R. / Mahesh, Vedamurthy. B. / Suman, Ankit Kumar / Velagapudi, Mohan Teja | 2020
Feasibility study on strength and flexural behaviour of RC beams with foundry fine aggregate
A., Shashi Kumar / Narayana, G. / Narendra, B. K. / Murthy, Narasimha | 2020
Aerodynamic design and optimization of supersonic inlets for external compression
Shashi, V. Kumar / Archana, Sridhar / Chaithanya, Kumar K. L. / Poojita, Srinivasan / Mukesh, M. | 2020
Enhanced process parameters using TOPSIS method during wire electro discharge machining of TiNiCo shape memory alloy
Soni, Hargovind / Narendranath, S. / Ramesh, M. R. / Mashinini, P. M. | 2020
Prediction of specific energy using dominant frequency of acoustics produced during diamond core drilling operations
Vijaya Kumar, Ch. / Murthy, Ch. S. N. / Vardhan, Harsha | 2020
Effect of PP and PP/MWCNT-COOH nanocomposites on mechanical properties
Poornima, C. / Sheshadri, C. E. Pavan / Mallik, U. S. | 2020
Influence of machining cutting speed on cutting force, tool flank wear on PVD inserts by turning of Ti-6Al-4V alloy
Raghavendra, M. J. / Ramachandra, C. G. / Srinivas, T. R. / Pai, M. Prashanth | 2020
Effect of friction stir processing on the dry sliding wear behavior of AZ31 Mg alloy
Diksangi, Siddramesh S. / Kulkarni, Sourabh / Edachery, Vimal / Pariyar, Abhishek / Kumar, Santosh | 2020
Hygrothermal response analysis of MEE beam embedded in adaptive wood through FE methods
Mahesh, Vinyas / Ravichandra, Hemanth Nagavara / Kattimani, Subhaschandra / Nagaraja, Chethan Vemagal | 2020
An experimental study on finding rheological properties of fresh conventional vibrated concrete mixes using concrete shear box
Ajay, N. / Girish, S. | 2020
Feasibility study for optimal cropping pattern for available water in the distributary of an irrigation system
Kumar, S. B. Ganesh / Ramesh, B. R. / Surendra, H. J. | 2020
Effect of thickness and modulus of masonry on the width of equivalent diagonal strut of masonry infill
A., Lakshmikantha B. / L., Shobha / Ganesh, Bharathi / R., Prabhakara | 2020
Feasibility study on augment drinking water supply and improve ground water table by 3rd stage lift irrigation scheme for Honakere, Karnataka
Mahalingegowda, H. R. / Narendra, B. K. | 2020
Studies on blasting effects of shock waves from a small – Scale shock tube
Singh, Anugya / Aravind, S. / Kannan, B. T. | 2020
Investigation of iron ores based on the bond grindability test
Harish., H. / Vardhan, Harsha / Raj, M. Govinda / Kaza, Marutiram / Sah, Rameshwar / Sinha, Abhishek / Kumar, S. Bharath | 2020
Finite element formulation of conjugate heat transfer in porous annulus
Ahamad, N. Ameer / Baig, Maughal Ahmed Ali / Ahmed, N. J. Salman / Kamangar, Sarfaraz / Khan, T. M. Yunus / Badruddin, Irfan Anjum / Reddy, Avala Raji / Khaleed, H. M. T. | 2020
Effect of cast thickness on properties of Al-Si cast obtained different by using vertical centrifugal
Sen, Smrutirekha / Reddy, Sudheer / Muralidhara, B. K. / Mukunda, P. G. | 2020
Analysis of stabilisation period of two lentic lake with marble powder
Shreyas, B. V. / Deepthi, B. P. / Vishwanath, K. N. | 2020
The wear properties of ceramic B4C/Al matrix composite at elevated temperature under dry sliding
Lakshmikantha, Rajesh Gandasi / Nanjundaswamy, Soundarya / Jayaprakash, Thilak Kumar / Ravindra, Rohan Kundwada / Auradi, Virupaxi | 2020
Preface: Proceedings of the 2nd International Conference on Emerging Research in Civil, Aeronautical and Mechanical Engineering (ERCAM)-2019
| 2020
Analysis of silo and comparing silo with different end condition
Krishna, R. R. Gagan / Prathap, H. K. Shiva / Narendra, B. K. / Mahadevaiah, T. | 2020
Earthquake analysis of multi storied reinforced concrete moment resistance building with vertical irregularity considering soil structure interaction for raft foundation
Parmar, Hemish. V. / Patel, Nilay. K. / Rana, Himesh. R. / Chandiwala, Anuj | 2020
Estimation of design flood at a reservior (outlet) by CWC based hydrometeriological approach
Kavya, B. M. / Kishan, S. / Arun, M. / Surendra, H. J. / Narandra, B. K. | 2020
Analysis of flexible pavement with steel slag as coarse aggregate
Muralidhara, R. / Danavandi, Varsha. S. / Das, Vivek. R. | 2020
Evaluation of strength properties of high volume fly ash concrete incorporating nanomaterials
Shashikumar, C. S. / Keshavamurthy, M. / Santhosh, B. S. | 2020
Identification of nozzle parameters in 3S device using artificial intelligence and meta-heuristic optimization scheme
Venkata Ramana, P. Gangadhar / Prabhu, L. | 2020
Metaheuristic optimal design of adaptive composite beams
Costa, D. M. S. / Loja, M. A. R. / Vinyas, M. | 2020
Design, fabrication and analysis of pen mold for injection molding machine
Kumar, Rishab / Singh, Robin / Singh, Ripu / Yadav, Sachidanand / Shetty, P. Balachndra / Yadav, Shiv Pratap Singh | 2020

Ähnliche Titel