Monitoring of Axial and Radial Creep of Coolant Channels in Operating PHWRs (Englisch)

Wie erhalte ich diesen Titel?

Expansion of coolant channels due to creep and growth is one of the major life limiting parameters of coolant channels in Pressurized Heavy Water Reactors (PHWRs). The environment of high stress, temperature and neutron irradiation causes axial and radial creep in pressure tubes. Creep monitoring of coolant channels is required to be done periodically in PHWRs as part of life management program for coolant channels. Axial and Radial creep measurement techniques ha e been developed by Refuelling Technology Division (RTD), Bhabha Atomic Research Centre (BARC) and successfully implemented in Indian PHWRs.

Inhaltsverzeichnis Konferenzband

Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.

2
Influence of chemical composition and heat treatment on long-term creep strength of grade 91 steel
Kimura, K. / Sawada, K. / Kushida, H. / Toda, Y. | 2013
10
Advances in Low-Temperature (<0.25Tm) Creep Behavior of Single and Two-Phase Titanium Alloys
Ankem, Sreeramamurthy / Wyatt, Zane W. / Joost, William | 2013
17
Creep and Low Cycle Fatigue Behaviour of Fast Reactor Structural Materials
Mathew, M.D. / Laha, K. / Sandhya, R. | 2013
36
Effect of Nitrogen on Evolution of Dislocation Substructure in 316LN SS During Creep
Ganesan, V. / Mathew, M.D. / Parameswaran, P. / Laha, K. | 2013
41
Creep-Induced Microstructural Changes in Large Welded Joints of High Cr Heat Resistant Steel
Tanaka, Yuta / Kubushiro, Keiji / Takahashi, Satoshi / Saito, Noriko / Nakagawa, Hirokatsu | 2013
45
Comparison of Creep Properties of Four Copper Alloys and Creep Based Stress Analysis of a Rocket Engine Combustion Chamber
Asraff, A.K. / Aparna, R. / Kumaresan, D. / Muthukumar, R. | 2013
51
Influence of Ru Addition on Microstructure, Creep and Rupture Properties of Nickel based DS Superalloy
Chatterjee, D. / Hazari, N. / Das, N. | 2013
58
Improvement in Creep Damage Tolerance of 14Cr-15Ni-Ti Modified Stainless Steel by Addition of Minor Elements
Latha, S. / Mathew, M.D. / Parameswaran, P. / Laha, K. / Selvi, S.Panneer / Mannan, S.L. | 2013
64
Creep Deformation and Rupture Behaviour of P92 Steel at 923 K
Samuel, E.Isaac / Choudhary, B.K. / Palaparti, D.P. Rao / Mathew, M.D. | 2013
70
Creep properties of grade 91 steel steam generator tube at 923 K
Palaparti, D.P. Rao / Samuel, E. Isaac / Choudhary, B.K. / Mathew, M.D. | 2013
78
Effect of Prior Cold Work on Creep Rupture and Tensile Properties of 14Cr-15Ni-Ti Stainless Steel
Vijayanand, V.D. / Nandagopal, M. / Parameswaran, P. / Laha, K. / Mathew, M.D. | 2013
82
Hot-tensile data and creep properties derived there-from for 316L(N) stainless steel with various nitrogen contents
Sreenivasan, P.R. | 2013
88
Creep Behaviour of 9CrMoNbV (P91) Steel Having a Small Amount of Boron
Baral, J. / Swaminathan, J. / Ghosh, R.N. | 2013
93
Mechanism for Grain Refinement and Mechanical Properties of AZ91 Mg Alloy by Carbon Inoculation
Suresh, M. / Srinivasan, A. / Pillai, U.T.S. / Pai, B.C. | 2013
98
Effect of Antimony and Yttrium Addition on the High Temperature Properties of AZ91 Magnesium Alloy
Boby, Arun / Ravikumar, K.K. / Pillai, U.T.S. / Pai, B.C. | 2013
103
Influence of Neodymium Addition on the Microstructure, Mechanical and Thermal Properties of Mg-Si Alloys
Kumar, K.K.Ajith / Viswanath, Abhilash / Pillai, U.T.S. / Pai, B.C. / Chakraborty, M. | 2013
109
Creep behavior of AZ91 magnesium alloy
Srinivasan, A. / Ajithkumar, K.K. / Swaminathan, J. / Pillai, U.T.S. / Pai, B.C. | 2013
114
Mechanisms of high temperature damage in elastoplastic cyclic loading of nickel superalloys and TiAl Intermetallics
Polak, Jaroslav / Obrtlik, Karel / Petrence, Martin / Man, Jiri / Kruml, Tomas | 2013
123
Secondary Hardening Behavior in Super Duplex Stainless Steels during LCF in Dynamic Strain Ageing Regime
Chai, Guocai / Andersson, Marcus | 2013
128
Evaluation of Low Cycle Fatigue Damage in Grade 91 Steel Weld Joints for High Temperature Applications
Shankar, Vani / Mariappan, K. / Sandhya, R. / Mathew, M.D. | 2013
136
Low Cycle Fatigue and Cyclic Plasticity Behavior of Indian PHWR/AHWR Primary Piping Material
Goyal, Sumit / Gupta, S.K. / Sivaprasad, S. / Tarafder, S. / Bhasin, V. / Vaze, K.K. / Ghosh, A.K. | 2013
144
Effect of Shot Peening on Low Cycle Fatigue Life of Compressor Disc of a Typical Fighter Class Aero-Engine
Sahoo, Benudhar / Satpathy, R.K. / Prasad, Kartik / Ahmed, Shahnawaz / Kumar, Vikas | 2013
149
Comparative Evaluation of the Low Cycle Fatigue Behaviours of P91 and P92 Steels
Kannan, R. / Sankar, Vani / Sandhya, R. / Mathew, M.D. | 2013
154
Microstructural Characterization of Fatigue and Creep-Fatigue Damaged 316L(N) Stainless Steel Through Ultrasonic Measurements
Palanichamy, P. / Srinivasan, V.S. / Jayakumar, T. / Rajendran, V. | 2013
160
Creep and creep-fatigue behaviour of 316 stainless steel
Holmström, Stefan / Pohja, Rami / Nurmela, Asta / Moilanen, Pekka / Auerkari, Pertti | 2013
165
Analysis of Hysteresis Loops of 316L(N) Stainless Steel under Low Cycle Fatigue Loading Conditions
Roy, Samir Chandra / Goyal, Sunil / Sandhya, R. / Ray, S.K. | 2013
171
Low Cycle Fatigue Behaviour of a Cu-Cr-Zr-Ti Alloy
Biswas, A. / Nagesha, A. / Sukumaran, G. / Parameswaran, P. / Asraff, A.K. / Sandhya, R. / Ray, S.K. | 2013
176
Effect of Strain Rate on the Low Cycle Fatigue Behavior of 316L(N) Stainless Steel Weld Joints
Chandra, Sayan Kalyan / Shankar, Vani / Mariappan, K. / Sandhya, R. / Chakraborty, P.C. | 2013
181
Is thermomechanical fatigue life predictable?
Christ, H.J. | 2013
191
Influence of interface roughness, substrate and oxide-creep on damage evolution and lifetime of plasma sprayed zirconia-based thermal barrier coatings
Beck, Tilmann / Schweda, Mario / Singheiser, Lorenz | 2013
199
Thermomechanical Fatigue Behaviour of a Modified 9Cr-1Mo Ferritic-Martensitic Steel
Nagesha, A. / Kannan, R. / Sandhya, R. / Sastry, G.V.S. / Mathew, M.D. / Rao, K. Bhanu Sankara / Singh, Vakil | 2013
204
Microstructural analysis of TMF failure mechanism of GTD-111 applied to gas turbine blades
Kim, Yongseok / Lee, Dong-Keun / Shin, In-Hwan / Koo, Jae-Mean / Seok, Chang-Sung | 2013
210
Assessment of the Characteristic of Thermal Barrier Coating Applied to Gas Turbine Blade by Thermo-Gradient Mechanical Fatigue Test
Shin, In-Hwan / Lee, Dong-Keun / Kim, Yong-Seok / Koo, Jae-Mean / Seok, Chang Sung / Lee, Tack-Woon | 2013
214
Qualification of Ni-based alloys for advanced ultra supercritical plants
Maile, K. | 2013
221
Nickel-Base Alloy Solutions for Ultrasupercritical Steam Power Plants
Klarstrom, Dwaine L. / Pike, L.M. / Ishwar, V.R. | 2013
226
Development of nickel alloys based on alloy 617 for components in 700°C power plants
Klöwer, J. / Husemann, R.U. / Bader, M. | 2013
232
Creep and LCF Behaviors of Newly Developed Advanced Heat Resistant Austenitic Stainless Steel for A-USC
Chai, Guocai / Boström, Magnus / Olaison, Magnus / Forsberg, Urban | 2013
240
Creep behaviour of thick-wall Alloy 617 seamless pipes for 700 °C power plant technology
Knezevic, V. / Schneider, A. / Landier, C. | 2013
246
Nickel Base Superalloys for Next Generation Coal Fired AUSC Power Plants
Patel, Shailesh J. / DeBarbadillo, John J. / Baker, Brian A. / Gollihue, Ronald D. | 2013
253
High Temperature Alloy Development for Future Nuclear Systems in Korea
Jeong, Yong-Hwan / Kim, Sung-Ho / Kim, Weon-Ju / Park, Ji-Yeon / Kwon, Junhyun / Jang, Jinsung / Kim, Tae-Kyu | 2013
259
High temperature materials for nuclear fast fission and fusion reactors and advanced fossil power plants
Jayakumar, T. / Mathew, M.D. / Laha, K. | 2013
271
Effects of Tungsten and Tantalum on Creep Deformation and Rupture Properties of Reduced Activation Ferritic-Martensitic Steel
Vanaja, J. / Laha, K. / Mathew, M.D. / Jayakumar, T. / Kumar, E.Rajendra | 2013
277
Effect of Tungsten on Mechanical Properties of Reduced Activation Ferritic-Martensitic Steel Subjected to Intercritical Heat Treatment
Sasmal, C.S. / Chandravathi, K.S. / Nandagopal, M. / Selvi, S.Panneer / Parameswaran, P. / Laha, K. / Mathew, M.D. / Jayakumar, T. / Kumar, E.Rajendra | 2013
284
A Preliminary Development and Characterization of Ni-based ODS Alloys
Jang, Jinsung / Kim, Tae-Kyu / Han, Chang-Hee / Min, Hyung-Ki / Jeong, Seog-Hwan / Kim, Do-Hyang | 2013
289
Microstructural Damage Evaluation in Ni-based Superalloy Gas Turbine Blades by Fractal Analysis
Tarafder, Mita / Sujata, M. / Ranganath, V.R. / Tarafder, S. / Bhumik, S.K. | 2013
295
Microstructural Modifications Due to Tungsten and Tantalum in 9Cr Reduced Activation Ferritic Martensitic Steels on Creep Exposure
Mythili, R. / Ravikirana / Vanaja, J. / Laha, K. / Saroja, S. / Jayakumar, T. / Mathew, M.D. / Rajendrakumar, E. | 2013
300
Eurofer Steel, Development to Full Code Qualification
Tavassoli, Farhad | 2013
309
Creep-fatigue evaluation methodologies and related issues for Japan sodium cooled fast reactor (JSFR)
Asayama, Tai / Takaya, Shigeru / Nagae, Yuji / Ando, Masanori / Tsukimori, Kazuyuki | 2013
314
Recent status of ASME code on creep strength enhanced ferritic steels
Masuyama, Fujimitsu / Shingledecker, John P. | 2013
326
Evaluation of Creep-fatigue Damage for Heat Exchangers in the Stella Sodium Test Loop
Lee, Hyeong-Yeon / Lee, Yong-Bum / Kim, Jong-Bum | 2013
333
Analysis of Interaction of Calandria Tubes with the End Shields in Advanced Heavy Water Reactor (AHWR)
Dureja, A.K. / Sinha, S.K. / Sinha, R.K. | 2013
342
Evaluation of Creep Deformation and Mechanical Properties of Nickel-based Superalloys through FE Analysis Based on Crystal Plasticity Models
Samal, M.K. / Ghosh, S. | 2013
348
Creep Transition of a Thin Rotating Annular Disk of Exponentially Variable Thickness with Inclusion and Edge Load
Sharma, Sanjeev / Sahai, Ila / Kuma, Ravindra | 2013
355
Assessment of Design Safety Limits for Fuel Cladding Based on Benchmark Tests
Sarkar, Rosy / Kumar, R.Suresh / Raghu, N. / Chellapandi, P. / Chetal, S.C. | 2013
361
Stress Indices for Non-Radial Branch Connections for Piping
Sajish, S.D. / Sati, Bhuwan Chandra / Jalaldeen, S. / Selvaraj, P. / Chellapandi, P. | 2013
367
A Generalized Geometric Shape Function for Evaluation of SIF Values of Thin-Walled Axially-Cracked Fuel Pin Specimens
Samal, M.K. / Sanyal, G. | 2013
374
Robust mesh insensitive structural stress method for fatigue analysis of welded structures
Selvakumar, P. / Hong, J.K. | 2013
380
Creep/fatigue crack growth testing, modelling and component life assessment of welds
Nikbin, Kamran | 2013
394
Microstructural degradation in power plant steels and life assessment of power plant components
Singh, Kulvir / Kamaraj, M. | 2013
402
Effect of Boron on Creep Behaviour of Inter-Critically Annealed Modified 9Cr-1Mo Steel
Das, C.R. / Albert, S.K. / Swaminathan, J. / Bhaduri, A.K. / Murty, B.S. | 2013
408
Effect of Joining Process on the Accumulation of Creep Deformation and Cavitation Across the Weld Joint of 316L(N) Stainless Steel
Sakthivel, T. / Vasudevan, M. / Laha, K. / Parameswaran, P. / Chandravathi, K.S. / Mathew, M.D. / Bhaduri, A.K. | 2013
414
Weld behavior of martensitic steels and Ni-based alloys for high temperature components
Klenk, Andreas / Speicher, Magdalena / Maile, Karl | 2013
421
Real-Time Monitoring of High Temperature Components
Daga, Rajesh / Samal, Mahendra Kumar | 2013
428
Remaining Life Related Issues Being Pursued at DRDO for Indian Air Force
Kumar, Vikas | 2013
433
Effects of Boron and Cerium on Creep Rupture Properties of Modified 9Cr-1Mo Steel and its Weld Joint
Chandravathi, K.S. / Laha, K. / Shinya, Norio / Mathew, M.D. | 2013
438
Role of Microstructure on Creep Rupture Behaviour of Similar and Dissimilar Joints of Modified 9Cr-1Mo Steel
Parameswaran, P. / Laha, K. | 2013
443
Burst and Biaxial Creep of Thin-Walled Tubing of Low c/a-Ratio HCP Metals
Murty, K.Linga / Seok, C.S. / Kombaiah, B. | 2013
451
Evaluation of Speed Lowering of Primary Sodium Pump into Sodium Pool for 500 MWe PFBR Based on Creep Damage
Chellapandi, P. / Kumar, R.Suresh / Jalaldeen, S. / Selvaraj, P. / Chetal, S.C. | 2013
457
Low Cycle Fatigue Damage of Mod.9Cr-1Mo Steel under Non-Proportional Multiaxial Loading
Itoh, Takamoto / Fukumoto, Kenichi / Hagi, Hideki / Itoh, Akira / Saitoh, Daichi | 2013
463
Monitoring of Axial and Radial Creep of Coolant Channels in Operating PHWRs
Patel, R.J. / Ranjon, R. / Battacharyya, S. / Sharma, G. | 2013
470
Experience with the operation of a test-rig for 700°C power plant materials
Metzger, K. / Czychon, K.H. / Zickler, S. / Maile, K. | 2013
474
Effect of Multiaxiality on the Creep Rupture Properties of 316L(N) SS
Charde, S.R. / Prasad, M.L. / Ballal, A.R. / Peshwe, D.R. / Mathew, M.D. / Paretkar, R.K. | 2013
481
Fretting Fatigue in Aircraft Components Made of Ti-Al-V Alloys
Sujata, M. / Madan, M. / Raghavendra, K. / Bhaumik, S.K. | 2013
487
Fatigue Failure of a Distortion Screen during Testing
Biswas, Swati / Kumar, Jivan / Ganeshachar, M.D. / Babu, S.N.Narendra / Ramachandra, S. | 2013
493
A comparative assessment of local and nonlocal damage models for prediction of fracture behavior during mixed-mode loading
Samal, M.K. / Seidenfuss, M. / Roos, E. | 2013
499
Current practices in structural analysis and testing of aero-engine main shafts
Kumar, Sanju / Rao, Rashmi / Rajeevalochanam, B.A. | 2013
510
Effect of multiaxial state of stress on creep rupture behaviour of 2.25Cr-1Mo steel
Goyal, Sunil / Laha, K. / Vijayanand, V.D. / Panneer Selvi, S. / Mathew, M.D. | 2013
517
Effect of Notch on Creep Behavior of 316L(N) SS
Charde, S.R. / Ballal, A.R. / Peshwe, D.R. / Mathew, M.D. / Paretkar, R.K. | 2013
526
Effect of Notch on Creep Behavior of 316L(N) SS Weld Joint
Charde, S.R. / Ballal, A.R. / Peshwe, D.R. / Mathew, M.D. / Paretkar, R.K. | 2013
534
Creep Behaviour of 316L(N) SS in the Presence of Notch
Kumar, J.Ganesh / Ganesan, V. / Vijayanand, V.D. / Laha, K. / Mathew, M.D. | 2013
542
Effect of Thermal Gradient on Steady State Creep in a Rotating Disc of Variable Thickness
Garg, Manish / Salaria, B.S. / Gupta, V.K. | 2013
548
Stress Rupture Properties of 316L(N) Stainless Steel under the Influence of Multiaxiality at Various Stress Levels
Prasad, M. Lakshmi / Ballal, A.R. / Paretkar, R.K. / Peshwe, D.R. | 2013
553
Finite Element Simulation of Cyclic Ball Indentation on Zr 2.5 wt.% Nb Alloy and Assessment of the Residual Stress Produced
Chatterjee, S. / Madhusoodanan, K. / Kayal, J.N. | 2013
561
Impression Creep Behaviour of U−6%Zr Alloy: Role of Microstructure
Kutty, T.R.G. / Kaity, Santu / Kumar, Arun | 2013
566
Dynamic Strain Ageing in AISI 316L Type Stainless Steel as Revealed by Indentation Creep Studies
Prasanna, H.Udaya / Udupa, K.Rajendra | 2013
573
Multifunctional high precision pneumatic loading system (HIPS) for creep-fatigue testing
Pohja, Rami / Nurmela, Asta / Moilanen, Pekka / Holmström, Stefan | 2013
578
Investigation of Fracture Behavior of Steam Generator Tubes of Indian PHWR using PLT Specimens
Sanyal, G. / Samal, M.K. | 2013
585
Application of Impression Creep Technique for Development of Creep Resistant Austenitic Stainless Steel
Naveena / Vijayanand, V.D. / Ganesan, V. / Laha, K. / Mathew, M.D. | 2013
591
Advances in Creep Damage/Life Assessment Technology for Creep Strength Enhanced Ferritic Steels
Masuyama, Fujimitsu | 2013
599
Creep Life Predictions of Engineering Components: Problems & Prospects
Ghosh, R.N. | 2013
607
Creep-fatigue lifetime assessment with phenomenological and constitutive material laws
Linn, Stefan / Scholz, Alfred / Wang, Peng / Lyschik, Matthias / Oechsner, Matthias | 2013
612
Predicting Remaining Creep Life using Damage Mechanics Principles
Le May, Iain | 2013
616
Design Life Prediction of Structural Components Subjected to Various Fatigue Loadings
Firdous, Imran / Harmain, G.A. / Masoodi, Junaid H. | 2013
625
Experimental and Numerical Study to Predict Residual Growth in an Aeroengine Compressor Disc After Overspeed
Ayyappan, C. / Kumar, Rajesh / Ramesh, P. / Jain, Rajeev | 2013
631
A Study on Fatigue Life Prediction of Ni-base Superalloy
Lee, Dongkeun / Shin, Inhwan / Kim, Yongseok / Koo, Jae-Mean / Seok, Chang-Sung | 2013
636
Damage mechanisms and fatigue lives: from the low to the very high cycle regime
Mughrabi, Hael | 2013
645
High temperature fatigue of nickel-based superalloys during high frequency testing
Zimmermann, M. / Stoecker, C. / Christ, H.J. | 2013
650
Effect of Temperature on Ratcheting Behaviour of 316LN SS
Sarkar, Aritra / Nagesha, A. / Sandhya, R. / Mathew, M.D. | 2013
655
Extension of Ruiz Criterion for Evaluation of 3-D Fretting Fatigue Damage Parameter
Anandavel, K. / Prakash, Raghu V. | 2013
661
Fretting Fatigue and Wear Behaviour of Timetal 834
Garg, Rahul / Rao, G.Sudhakar / Bhartia, Vikash / Singh, Vakil | 2013
666
Ratcheting Strain Assessment in Pressurised Stainless Steel Elbows Subjected to In-plane Bending
Vishnuvardhan, S. / Raghava, G. / Gandhi, P. / Goyal, Sumit / Gupta, Suneel K. / Bhasin, Vivek | 2013
671
Low and High Cycle Fatigue Behavior of Nickel-base Alloy at High Temperatures
Chai, Guocai / Liu, Ping / Zhou, Nian / Frodigh, Johan | 2013
677
Subcritical Crack Growth on Crystallographic Planes in a Ni-base Superalloy: Relevance to Orientations
Okazaki, M. / Sakaguchi, M. / Yamagishi, S. | 2013
685
Assessment of Deformation Behavior of Zr-2.5Nb Alloy during Thermo-Mechanical Processing and under Service Condition
Chakravartty, J.K. / Singh, R.N. / Sarkar, A. | 2013
693
Cyclic Fracture, FCG and Ratcheting Studies on Type 304LN Stainless Steel Straight Pipes and Elbows
Raghava, G. / Gandhi, P. / Vaze, K.K. | 2013
699
Fatigue Crack Growth Studies on SA403 TP 304LN SS Elbows
Pukazhendhi, D.M. / Raghava, G. / Knight, G.M.Samuel | 2013
703
Fatigue Crack Growth Behavior in Pipes and Elbows of Carbon Steel and Stainless Steel Materials
Arora, Punit / Singh, P.K. / Bhasin, V. / Vaze, K.K. / Pukazhendhi, D.M. / Gandhi, P. / Raghava, G. | 2013
710
On the Application of Rousselier's Damage Model to Predict Fracture Resistance Behavior of Zircaloy Fuel Pin Specimens
Samal, M.K. / Shah, P.K. | 2013
716
Fatigue Crack Growth Behavior of 316LN Stainless Steel with Different Nitrogen Contents
Babu, M.Nani / Dutt, B.Shashank / Venugopal, S. / Sasikala, G. / Albert, Shaju K. / Bhaduri, A.K. / Jayakumar, T. | 2013
722
Fatigue Crack Growth Characterisation of RAFM Steel using Acoustic Emission Technique
Babu, M.Nani / Mukhopadhyay, C.K. / Sasikala, G. / Dutt, B.Shashank / Venugopal, S. / Albert, Shaju K. / Bhaduri, A.K. / Jayakumar, T. | 2013
727
A Comprehensive Creep Model for Advanced 9-10% Cr Ferritic Steels
Oruganti, Ramkumar / Karadge, Mallikarjun / Swaminathan, Srinivasan | 2013
735
Modeling Creep Behaviour of Boiler Grade Steels - Application to Grade 92 Steel
Cini, E. / Desdoit, E. / Villani, A. / Besson, J. | 2013
742
Effect of Temperature and Strain Amplitude on Fatigue Behaviour of BCC Iron Single Crystal using Molecular Dynamics Simulation
Srinivasan, V.S. / Sainath, G. / Choudhary, B.K. / Mathew, M.D. / Jayakumar, T. | 2013
747
Modeling the Effect of Grain Boundary Sliding on Creep Lifetime: Application to Two Austenitic Stainless Steels
Mahesh, Sivasambu / Mathew, M.D. | 2013
751
Creep Modelling of P91 Steel for High Temperature Power Plant Applications
Nandi, Somnath / Vikrant, K.S.N. / Ahv, Pavan / Singh, Kulvir / Ghosh, R.N. | 2013
756
Prediction of Creep Curves of High Temperature Alloys using θ -Projection Concept
Omprakash, C.M. / Kumar, A. / Srivathsa, B. / Satyanarayana, D.V.V. | 2013
760
Modeling Steady State Creep Behavior of Functionally Graded Thick Cylinder in the Presence of Residual Stress
Singh, Tejeet / Gupta, V.K. | 2013
768
Modeling of the Effect of a Defect on HCF Life of a Magnesium AZ91 Specimen Subjected to Transverse Load
Murugan, G. / Raghukandan, K. / Pillai, U.T.S. / Pai, B.C. | 2013
774
Modeling and Finite Element Simulation of Low Cycle Fatigue Behaviour of 316 SS
Shit, J. / Dhar, S. / Acharyya, S. | 2013
780
Prediction of temperature dependence and scatter in fracture toughness of pressure vessel steel using nonlocal damage models
Samal, M.K. / Seidenfuss, M. / Roos, E. | 2013
786
Analysis of Damage Accumulations in High Strength Low Alloy Steels under Monotonic Deformation
Das, Arpan / Das, S.K. / Sivaprasad, S. / Tarafder, M. / Tarafder, S. | 2013
793
Creep-fatigue Damage Analysis of Lower Stay Plate in Control Plug
Pandey, S.K. / Jalaldeen, S. / Selvaraj, P. / Chellapandi, P. | 2013
798
Continuum Damage Mechanics Approach to Predict Creep Behaviour of Modified 9Cr-1Mo Ferritic Steel at 873 K
Christopher, J. / Sainath, G. / Srinivasan, V.S. / Samuel, E.Isaac / Choudhary, B.K. / Mathew, M.D. / Jayakumar, T. | 2013
805
Stochastic Creep Damage Growth Due to Random Thermal Fluctuations Using Continuum Damage Mechanics
Appalanaidu, Y. / Vyas, Yash / Gupta, Sayan | 2013
812
Fatigue behaviour of a martensitic and an austenitic steel in heavy liquid metals
Vogt, Jean-Bernard / Proriol-Serre, Ingrid | 2013
819
Creep and Oxidation Behaviors of Alloy 617 in Air and Helium Environments at 1173 K
Kim, Woo-Gon / Lee, Gyeong-Geun / Park, Ji-Yeon / Hong, Sung-Deok / Kim, Yong-Wan | 2013
823
A Comparison of Creep Deformation and Rupture Behaviour of 316L(N) Austenitic Stainless Steel in Flowing Sodium and in Air
Ravi, S. / Laha, K. / Mathew, M.D. / Vijayaraghavan, S. / Shanmugavel, M. / Rajan, K.K. / Jayakumar, T. | 2013
830
Effect of Salt Coatings on Low Cycle Fatigue Behavior of Nickel -base Superalloy GTM-SU-718
Mahobia, G.S. / Sudhakar, R.G. / Antony, Ajesh / Chattopadhyay, K. / Srinivas, N.C. Santhi / Singh, Vakil | 2013
835
Effect of Prior Cyclic Oxidation on the Creep Behavior of Bare and Pt-Aluminide Coated Directionally Solidified CM-247LC Alloy
Alam, Md Zafir / Satyanarayana, D.V.V. / Chatterjee, D. / Sarkar, R. / Das, D.K. | 2013
842
Experience in Long Term Operation of Sodium Loop for Creep Experiments in Dynamic Sodium at High Temperature
Rajasundaram, P. / Vijayaraghavan, S. / Chandran, T. / Shanmugavel, M. / Shanmugasundaram, M. / Ravi, S. / Laha, K. / Babu, B. / Mathew, M.D. / Rajan, K.K. | 2013