Direct Imprinting Using Magnetic Nickel Mold and Electromagnetism Assisted Pressure for Replication of Microstructures (Englisch)
- Neue Suche nach: Weng, Y.-J.
- Neue Suche nach: Weng, Y.-J.
In:
International Polymer Processing
;
26
, 5
; 484-489
;
2011
- Aufsatz (Zeitschrift) / Print
-
Titel:Direct Imprinting Using Magnetic Nickel Mold and Electromagnetism Assisted Pressure for Replication of Microstructures
-
Beteiligte:Weng, Y.-J. ( Autor:in )
-
Erschienen in:International Polymer Processing ; 26, 5 ; 484-489
-
Verlag:
- Neue Suche nach: De Gruyter
-
Erscheinungsort:Berlin
-
Erscheinungsdatum:2011
-
ISSN:
-
ZDBID:
-
DOI:
-
Medientyp:Aufsatz (Zeitschrift)
-
Format:Print
-
Sprache:Englisch
- Neue Suche nach: 51.70 / 58.22
- Weitere Informationen zu Basisklassifikation
- Neue Suche nach: 020/5755
-
Schlagwörter:
-
Klassifikation:
-
Datenquelle:
Inhaltsverzeichnis – Band 26, Ausgabe 5
Zeige alle Jahrgänge und Ausgaben
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- 469
-
Contents| 2011
- 470
-
Applicability of the Impact Response Analysis Method for Reinforced Concrete Beams Mixed with Polyvinyl Alcohol Short FibersBhatti, A Q et al. | 2011
- 478
-
Epoxy-Montmorillonite Nanocomposites Applied to Powder CoatingsPiazza, D. / Lorandi, N. P. / Rieder, E. S. / Scienza, L. C. / Zattera, A. J. et al. | 2011
- 484
-
Direct Imprinting Using Magnetic Nickel Mold and Electromagnetism Assisted Pressure for Replication of MicrostructuresWeng, Y-J et al. | 2011
- 490
-
Automated Mold Heating System Using High Frequency Induction with Feedback Temperature ControlPark, K et al. | 2011
- 498
-
The Prediction of Bowing Distortion of Film after Transverse Stretching with Consideration of Heated Air Flow in a TenterTokihisa, M. / Kushizaki, Y. / Tomiyama, H. / Yamamoto, Y. / Yamada, T. et al. | 2011
- 508
-
The Influence of Injection Molding and Injection Compression Molding on Ultra-high Molecular Weight Polyethylene Polymer MicrofabricationKuo, H.-C. / Jeng, M.-C. et al. | 2011
- 517
-
A Design-of-Experiment Study on the Microcellular Extrusion of Sub-critical CO2 Saturated PLA PelletsMiller, D et al. | 2011
- 525
-
Optimization of Injection Molding Process for SGF and PTFE Reinforced PC Composites Using Response Surface Methodology and Simulated Annealing ApproachYang, T. / Yang, Y.-K. / Chen, C.-Y. et al. | 2011
- 540
-
Flow Visualisation in Co-rotating Twin Screw Extruders: Positron Emission Particle Tracking and Numerical Particle TrajectoriesDiemer, J et al. | 2011
- 551
-
The Influence of Melt and Process Parameters on the Quality and Occurrence of Part Defects in Water-assisted Injection Molded TubesSannen, S et al. | 2011
- 560
-
Model and Numerical Simulation for the Second Penetration in Water-assisted Injection MoldingZhang, S. / Cao, W. / Zheng, G. / Jia, Z. / Shen, C. et al. | 2011
- 569
-
Influence of Extrusion Conditions on the Rheological Behavior of Nuclear Bituminized Waste ProductsMouazen, M. / Poulesquen, A. / Vergnes, B. et al. | 2011
- 580
-
Influence of Dicumyl Peroxide Content on Thermal and Mechanical Properties of PolylactideRytlewski, P et al. | 2011
- 587
-
Calculation of Average Residence Time in a Ko-kneaderVergnes, B. et al. | 2011
- 587
-
Rapid Communications - Calculation of Average Residence Time in a Ko-kneaderVergnes, B et al. | 2011
- 590
-
PPS News| 2011
- 591
-
Instructions to Authors| 2011
- 592
-
PPS Membership Application/Impressum| 2011
- 593
-
Yearly Index| 2011