Normal contact between rough surfaces by the Discrete Element Method (Englisch)
- Neue Suche nach: Jerier, J.F.
- Neue Suche nach: Molinari, J.F.
- Neue Suche nach: Jerier, J.F.
- Neue Suche nach: Molinari, J.F.
In:
Tribology International
;
47
;
1-8
;
2011
-
ISSN:
- Aufsatz (Zeitschrift) / Elektronische Ressource
-
Titel:Normal contact between rough surfaces by the Discrete Element Method
-
Beteiligte:Jerier, J.F. ( Autor:in ) / Molinari, J.F. ( Autor:in )
-
Erschienen in:Tribology International ; 47 ; 1-8
-
Verlag:
-
Erscheinungsdatum:30.08.2011
-
Format / Umfang:8 pages
-
ISSN:
-
DOI:
-
Medientyp:Aufsatz (Zeitschrift)
-
Format:Elektronische Ressource
-
Sprache:Englisch
-
Schlagwörter:
-
Datenquelle:
Inhaltsverzeichnis – Band 47
Zeige alle Jahrgänge und Ausgaben
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- 1
-
Normal contact between rough surfaces by the Discrete Element MethodJerier, J.F. / Molinari, J.F. et al. | 2011
- 9
-
Influence of surface velocity directions on lubricant film formation in EHL point contactsHoehn, B.-R. / Michaelis, K. / Mayer, J. / Weigl, A. et al. | 2011
- 16
-
Cavitation and high-velocity slurry erosion resistance of welded Stellite 6 alloyRomo, S.A. / Santa, J.F. / Giraldo, J.E. / Toro, A. et al. | 2011
- 25
-
Investigation of rolling contact fatigue damage process of the coating by acoustics emission and vibration signalsZhi-qiang, Zhang / Guo-lu, Li / Hai-dou, Wang / Bin-shi, Xu / Zhong-yu, Piao / Li-na, Zhu et al. | 2011
- 32
-
On the fretting crack nucleation with provision for size effectAghdam, A.B. / Beheshti, Ali / Khonsari, M.M. et al. | 2011
- 44
-
3D polymer nanostructures fabrication by AFM tip-based single scanning with a harder cantileverSun, Yang / Yan, Yongda / Hu, Zhenjiang / Zhao, Xuesen / Yan, Jiucun et al. | 2011
- 50
-
Comparative overview of five gear oils in mixed and boundary film lubricationBrandão, José A. / Meheux, Mathilde / Ville, Fabrice / Seabra, Jorge H.O. / Castro, Jorge et al. | 2011
- 62
-
Tribological behavior of plasma electrolytic oxidation coatings on the surface of Mg–8Li–1Al alloyMa, Chunxiang / Zhang, Milin / Yuan, Yi / Jing, Xiaoyan / Bai, Xuefeng et al. | 2011
- 69
-
Determination of a large tilting pad thrust bearing angular stiffnessSrikanth, D.V. / Chaturvedi, Kaushal K. / Reddy, A. Chenna Kesava et al. | 2011
- 77
-
The effect of basecoat pigmentation on the scratch resistance and weathering performance of an acrylic–melamine basecoat/clearcoat automotive finishRamezanzadeh, B. / Moradian, S. / Yari, H. / Kashani, A. / Niknahad, M. et al. | 2011
- 90
-
A study on the performance of a magnetic fluid based squeeze film in curved porous rotating rough annular plates and deformation effectShimpi, M.E. / Deheri, G.M. et al. | 2011
- 100
-
The numerical analysis of the radial sleeve bearing with combined surface slipWang, Li-li / Lu, Chang-hou / Wang, Min / Fu, Wen-xin et al. | 2011
- 105
-
An optimal forward extrusion device proposed for numerical and experimental analysis of materials tribological properties corresponding to bulk forming processesGavrus, A. / Francillette, H. / Pham, D.T. et al. | 2011
- 122
-
Adhesive wear and frictional performance of bamboo fibres reinforced epoxy compositeNirmal, Umar / Hashim, Jamil / Low, K.O. et al. | 2011
- 134
-
Pressure dam influence on the performance of gas face sealsFaria, Marco Tulio C. / Mendes Miranda, Wederley et al. | 2011
- 142
-
An empirical approach to explain the material removal rate for copper chemical mechanical polishingGuoshun, Pan / Ning, Wang / Hua, Gong / Yan, Liu et al. | 2011
- 145
-
Empirically derived optimization model: Theoretical formulation and validationZengeya, Miles / Gadala, Mohamed et al. | 2011
- 159
-
Nano–level finishing of single crystal silicon blank using magnetorheological finishing processSidpara, Ajay / Jain, V.K. et al. | 2011
- 167
-
Computational investigation of slip rate dependent friction as a potential contribution to displacement bursts in nanoindentation of nickelBerke, Péter Z. / Massart, Thierry J. et al. | 2011
- 175
-
Thin layer flow and film decay modeling for grease lubricated rolling bearingsVenner, C.H. / van Zoelen, M.T. / Lugt, P.M. et al. | 2011
- 188
-
Examination of the tribolayer formation of a self-lubricant W–S–C sputtered coatingPimentel, J.V. / Polcar, T. / Evaristo, M. / Cavaleiro, A. et al. | 2011
- 194
-
Characteristics of diesel engine soot that lead to excessive oil thickeningEsangbedo, Christine / Boehman, André L. / Perez, Joseph M. et al. | 2011
- 204
-
The effect of a novel CoCr electropolishing technique on CoCr-UHMWPE bearing frictional performance for total joint replacementsAlvarez, Estefania / Vinciguerra, John / DesJardins, John D et al. | 2011
- 212
-
Observation of triboelectron emission from real copper surfaces in sliding contact with polytetrafluoroethylene and polyimideMomose, Yoshihiro / Kubo, Kazuya et al. | 2011
- 221
-
Global energy consumption due to friction in passenger carsHolmberg, Kenneth / Andersson, Peter / Erdemir, Ali et al. | 2011
- 235
-
A new numerical analysis for piston skirt–liner system lubrication considering the effects of connecting rod inertiaMeng, Xianghui / Xie, Youbai et al. | 2011
- IFC
-
Editorial Board| 2012