Microstructure and mechanical characteristics of bulk polycrystalline Ni consolidated from blends of powders with different particle size (Englisch)
- Neue Suche nach: Liu, W.C.
- Neue Suche nach: Liu, W.C.
- Neue Suche nach: Man, C.-S.
- Neue Suche nach: Raabe, D.
In:
Materials science and engineering / A
;
527
, 4
; 1206-1215
;
2010
-
ISSN:
- Aufsatz (Zeitschrift) / Print
-
Titel:Microstructure and mechanical characteristics of bulk polycrystalline Ni consolidated from blends of powders with different particle size
-
Beteiligte:
-
Erschienen in:Materials science and engineering / A ; 527, 4 ; 1206-1215
-
Verlag:
- Neue Suche nach: Elsevier
-
Erscheinungsort:Amsterdam [u.a.]
-
Erscheinungsdatum:2010
-
ISSN:
-
ZDBID:
-
Medientyp:Aufsatz (Zeitschrift)
-
Format:Print
-
Sprache:Englisch
- Neue Suche nach: 51.00
- Weitere Informationen zu Basisklassifikation
- Neue Suche nach: 535/5100
-
Schlagwörter:
-
Klassifikation:
-
Datenquelle:
Inhaltsverzeichnis – Band 527, Ausgabe 4
Zeige alle Jahrgänge und Ausgaben
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- 875
-
Effect of thermal cycles on heavily cold deformed AISI 304L austenitic stainless steelKumar, B. Ravi / Das, S.K. / Sharma, Sailaja / Sahu, J.K. et al. | 2009
- 883
-
Multi-scale characterization of inhomogeneous morphologically textured microstructuresWilks, G.B. / Tschopp, M.A. / Spowart, J.E. et al. | 2009
- 890
-
Effect of thermal exposure on stress rupture properties of a Re bearing Ni base single crystal superalloyLiu, J.L. / Jin, T. / Yu, J.J. / Sun, X.F. / Guan, H.R. / Hu, Z.Q. et al. | 2009
- 898
-
Effect of recrystallization and grain growth on the mechanical properties of an extruded AZ21 Mg alloyAzeem, M.A. / Tewari, A. / Ramamurty, U. et al. | 2009
- 904
-
Deformation characteristics of Al-4043 alloySaad, G. / Fayek, S.A. / Fawzy, A. / Soliman, H.N. / Mohammed, Gh. et al. | 2009
- 911
-
The influence of phosphorus on the microstructure and stress-rupture properties in a low thermal expansion superalloyYu, L.X. / Sun, Y.R. / Sun, W.R. / Sun, X.F. / Guo, S.R. / Hu, Z.Q. et al. | 2009
- 917
-
Physico-mechanical properties and thermal stability of thermoset nanocomposites based on styrene-butadiene rubber/phenolic resin blendShojaei, Akbar / Faghihi, Morteza et al. | 2009
- 927
-
Characterization of ultra-fine grained steel samples produced by high pressure torsion via magnetic Barkhausen noise analysisBayramoglu, Sadik / Gür, C. Hakan / Alexandrov, Igor V. / Abramova, Marina M. et al. | 2009
- 934
-
Effect of the strain reversal on austenite–ferrite phase transformation in a Nb-microalloyed steelLanzagorta, J.L. / Jorge-Badiola, D. / Gutiérrez, I. et al. | 2009
- 941
-
Direct observation of microfracture process in metallic-continuous-fiber-reinforced amorphous matrix composites fabricated by liquid pressing processLee, Kyuhong / Son, Chang-Young / Lee, Sang-Bok / Lee, Sang-Kwan / Lee, Sunghak et al. | 2009
- 947
-
EBSD study of the substructure development with cold deformation of dual phase steelDillien, Steven / Seefeldt, Marc / Allain, Sébastien / Bouaziz, Olivier / Van Houtte, Paul et al. | 2009
- 954
-
Effect of microstructure and grain size on the fracture toughness of a micro-alloyed steelKumar, A. Seshu / Kumar, B. Ravi / Datta, G.L. / Ranganath, V.R. et al. | 2009
- 961
-
High temperature deformation behavior of hot isostatically pressed P/M FGH4096 superalloyNing, Yongquan / Yao, Zekun / Li, Hui / Guo, Hongzhen / Tao, Yu / Zhang, Yiwen et al. | 2009
- 967
-
Experimental and numerical study on effect of forming rate on AA5086 sheet formabilityZhang, Cunsheng / Leotoing, Lionel / Guines, Dominique / Ragneau, Eric et al. | 2009
- 973
-
Effect of Al additions on the age hardening response of the Mg–2.4Zn–0.1Ag–0.1Ca (at.%) alloy—TEM and 3DAP studyMendis, C.L. / Oh-ishi, K. / Hono, K. et al. | 2009
- 981
-
Effects of casting temperature on mechanical properties of Zr-based metallic glassesMao, J. / Zhang, H.F. / Fu, H.M. / Wang, A.M. / Li, H. / Hu, Z.Q. et al. | 2009
- 986
-
A direct comparison in the fatigue resistance enhanced by surface severe plastic deformation and shot peening in a C-2000 superalloyShaw, Leon L. / Tian, Jia-Wan / Ortiz, Angel L. / Dai, Kun / Villegas, Juan C. / Liaw, Peter K. / Ren, Ruiming / Klarstrom, Dwaine L. et al. | 2009
- 995
-
Enhanced chromizing kinetics of tool steel by means of surface mechanical attrition treatmentLu, S.D. / Wang, Z.B. / Lu, K. et al. | 2009
- 1003
-
Investigations on cold deformation mechanisms of the hydrogenated Ti–6Al–4V alloysSun, Zhonggang / Chen, Guoqing / Wang, Yaoqi / Zhou, Wenlong / Hou, Hongliang et al. | 2009
- 1008
-
The influences of precrack orientations in welded joint of Ti–6Al–4V on fatigue crack growthWang, Xuedong / Shi, Qingyu / Wang, Xin / Zhang, Zenglei et al. | 2009
- 1016
-
Effects of heat treatments on the microstructure of IN792 alloyYang, Jinxia / Zheng, Qi / Zhang, Hongyu / Sun, Xiaofeng / Guan, Hengrong / Hu, Zhuangqi et al. | 2009
- 1022
-
Influence of subsequent cold work on the superplastic properties of a friction stir welded (FSW) aluminium alloyKatsas, S. / Dashwood, R. / Jackson, M. / Grimes, R. et al. | 2009
- 1027
-
Processing and properties of nanocrystalline CuNiCoZnAlTi high entropy alloys by mechanical alloyingVaralakshmi, S. / Kamaraj, M. / Murty, B.S. et al. | 2009
- 1031
-
Investigation of particle size and amount of alumina on microstructure and mechanical properties of Al matrix composite made by powder metallurgyRahimian, Mehdi / Parvin, Nader / Ehsani, Naser et al. | 2009
- 1039
-
Fabrication and performance of Al2O3/(W,Ti)C+Al2O3/TiC multilayered ceramic cutting toolsJianxin, Deng / Zhenxing, Duan / Dongling, Yun / Hui, Zhang / Xing, Ai / Jun, Zhao et al. | 2009
- 1048
-
Effect of NaCl and CaCl2 additives on NaNO3 bath nitriding of steelLee, Min-ku / Kim, Dong-sam / Kim, Sung-chul / Han, Sang-won / Kim, Insoo / Lee, Dong Nyung et al. | 2009
- 1052
-
Hot deformation of 15-5 PH stainless steelAghaie-Khafri, M. / Adhami, F. et al. | 2009
- 1058
-
Microstructure and superelasticity of in situ synthesized (TiB+La2O3)/Ti-alloy composites with different mass fraction of LaB6Wang, Liqiang / Lu, Weijie / Qin, Jining / Zhang, Fan / Zhang, Di et al. | 2009
- 1063
-
Compressive strength and microstructure of carbon nanotubes–fly ash cement compositesChaipanich, Arnon / Nochaiya, Thanongsak / Wongkeo, Watcharapong / Torkittikul, Pincha et al. | 2009
- 1068
-
Characterization of precipitate evolution in an artificially aged Al–Zn–Mg–Sc–Zr alloyWu, Ling-Mei / Seyring, Martin / Rettenmayr, Markus / Wang, Wen-Hsiung et al. | 2009
- 1074
-
Effects of minor scandium on as-cast microstructure, mechanical properties and casting fluidity of ZA84 magnesium alloyPan, Fusheng / Yang, Mingbo / Cheng, Liang et al. | 2009
- 1082
-
Effects of Cu addition on the synergistic effects of Ti–B in thermomechanically processed low carbon steelsGhosh, S.K. / Bhowmik, N. / Haldar, A. / Chattopadhyay, P.P. et al. | 2009
- 1089
-
Precipitation behavior of the β phase in Al-5083Goswami, R. / Spanos, G. / Pao, P.S. / Holtz, R.L. et al. | 2009
- 1089
-
Precipitation behavior of the b phase in Al-5083Goswami, R. / Spanos, G. / Pao, P. S. / Holtz, R. L. et al. | 2010
- 1096
-
Brazing of carbon fiber reinforced SiC composite and TC4 using Ag–Cu–Ti active brazing alloyXiong, Jin Hui / Huang, Ji Hua / Zhang, Hua / Zhao, Xing Ke et al. | 2009
- 1102
-
Mechanical behavior of a PP platelet-reinforced nanocomposite: Experimental characterization and two scale modeling of linear and non-linear responseCauvin, L. / Kondo, D. / Brieu, M. / Bhatnagar, N. et al. | 2009
- 1109
-
Local deformation of Ti6Al4V modified 1wt% B and 0.1wt% CPoletti, C. / Warchomicka, F. / Degischer, H.P. et al. | 2009
- 1117
-
Anisotropic compressive behavior of closed-cell Al–Si alloy foamsMu, Yongliang / Yao, Guangchun et al. | 2009
- 1120
-
Tensile creep behavior and strain-rate sensitivity of superalloy GH4049 at elevated temperaturesChen, Lijie et al. | 2009
- 1126
-
Modeling of continuous dynamic recrystallization in commercial-purity aluminumHallberg, Håkan / Wallin, Mathias / Ristinmaa, Matti et al. | 2009
- 1135
-
Characterization of Fe–Cr–Mn–N amorphous powders with a wide supercooled liquid region developed by mechanical alloyingAmini, R. / Salahinejad, E. / Hadianfard, M.J. / Marasi, M. / Sritharan, T. et al. | 2009
- 1143
-
On the anomalous hardening during annealing of heavily deformed f.c.c. metalsJia, N. / Zhao, X. / Song, D. / Zhou, M.H. / Wang, Y.D. et al. | 2009
- 1151
-
Simulation of texture evolution and macroscopic properties in Mg alloys using the crystal plasticity finite element methodChoi, S.-H. / Kim, D.H. / Lee, H.W. / Shin, E.J. et al. | 2009
- 1160
-
Flow stress prediction at hot working conditionsMirzadeh, H. / Najafizadeh, A. et al. | 2009
- 1165
-
Development and validation of a processing map for Aermet100 steelJi, Guoliang / Li, Fuguo / Li, Qinghua / Li, Huiqu / Li, Zhi et al. | 2009
- 1172
-
A finite element study on localized deformation and functional fatigue in pseudoelastic NiTi stripsGrossmann, Christian / Schaefer, Andreas / Wagner, Martin F.-X. et al. | 2009
- 1179
-
Contact strength and crack formation in monolithic ceramic materialsHegedűsová, Lucia / Kovalčíková, Alexandra / Ceniga, Ladislav / Dusza, Ján et al. | 2009
- 1185
-
Creep-based life prediction modelling of aluminium in fireKandare, E. / Feih, S. / Kootsookos, A. / Mathys, Z. / Lattimer, B.Y. / Mouritz, A.P. et al. | 2009
- 1194
-
Mechanical properties and strain-hardening behavior of Mg alloy AZ31B-H24 thin sheetWu, Horng-Yu / Lin, Feng-Zheng et al. | 2009
- 1200
-
Influence of cooling rate after homogenization on the flow behavior of aluminum alloy 7050 under hot compressionLiu, Shengdan / You, Jianghai / Zhang, Xinming / Deng, Yunlai / Yuan, Yubao et al. | 2009
- 1206
-
Microstructure and mechanical characteristics of bulk polycrystalline Ni consolidated from blends of powders with different particle sizeDirras, G. / Gubicza, J. / Ramtani, S. / Bui, Q.H. / Szilágyi, T. et al. | 2009
- 1215
-
Microstructure and mechanical properties of laser welded DP600 steel jointsFarabi, N. / Chen, D.L. / Li, J. / Zhou, Y. / Dong, S.J. et al. | 2009
- 1223
-
Effect of Sn content on the structural and mechanical properties of Al–Si alloyAbd El-Salam, F. / Abd El-Khalek, A.M. / Nada, R.H. / Wahab, L.A. / Zahran, H.Y. et al. | 2009
- 1230
-
Effect of die channel angle, friction and back pressure in the equal channel angular pressing using 3D finite element simulationDjavanroodi, F. / Ebrahimi, M. et al. | 2009
- 1236
-
Optimization of annealing treatment parameters in a twin roll cast and warm rolled ZK60 alloy sheetChen, Hongmei / Yu, Huashun / Kang, Suk Bong / Cho, Jae Hyoung / Min, Guanghui et al. | 2009
- 1243
-
Microstructure and mechanical properties of nanoscale Cu/Ni multilayersZhu, X.Y. / Liu, X.J. / Zong, R.L. / Zeng, F. / Pan, F. et al. | 2009
- 1249
-
Effect of strain hardening on texture development in cold rolled Al–Mg alloyLiu, W.C. / Man, C.-S. / Raabe, D. et al. | 2009
- 1255
-
Tensile and creep behaviors of Mg–5Zn–2.5Er alloy improved by icosahedral quasicrystalLi, Jianhui / Du, Wenbo / Li, Shubo / Wang, Zhaohui et al. | 2009
- 1260
-
Mechanical characterisation of interpenetrating network metal–ceramic compositesScherm, F. / Völkl, R. / Neubrand, A. / Bosbach, F. / Glatzel, U. et al. | 2009
- 1266
-
Mechanical properties and deep drawability of Mg–Gd–Y–Zr alloy rolling sheet at elevated temperaturesLi, Li / Zhang, Xinming / Tang, Changping / Deng, Yunlai / Zhou, Nan et al. | 2009
- 1275
-
Open-celled porous Cu prepared by replication of NaCl space-holdersWang, Q.Z. / Cui, C.X. / Liu, S.J. / Zhao, L.C. et al. | 2009
- 1279
-
Erratum to “Damping capacity and dynamic mechanical characteristics of the plasma-sprayed coatings” [Mater. Sci. Eng. A 408 (2005) 42–46]Yu, Liming / Ma, Yue / Zhou, Chungen / Xu, Huibin et al. | 2005
- 1280
-
Corrigendum to “Effect of orientation and loading rate on compression behavior of small-scale Mo pillars” [Mater. Sci. Eng. A 508 (2009) 241–246]Schneider, A.S. / Clark, B.G. / Frick, C.P. / Gruber, P.A. / Arzt, E. et al. | 2009
- 1281
-
Corrigendum to “Effects of doping on thermal conductivity of pyrochlore oxides for advanced thermal barrier coatings” [Mater. Sci. Eng. A 459 (2007) 192–195]Bansal, Narottam P. / Zhu, Dongming / Eslamloo-Grami, Maryam et al. | 2007
- 1282
-
Author Index| 2009
- 1284
-
Subject Index| 2009
- CO2
-
Editorial Board| 2009