Additive manufacturing in unmanned aerial vehicles (UAVs): Challenges and potential (Englisch)
- Neue Suche nach: Goh, G.D
- Neue Suche nach: Goh, G.D
- Neue Suche nach: Agarwala, S
- Neue Suche nach: Goh, G.L
- Neue Suche nach: Dikshit, V
- Neue Suche nach: Sing, S.L
- Neue Suche nach: Yeong, W.Y
In:
Aerospace science and technology
;
63
; 140-151
;
2017
-
ISSN:
- Aufsatz (Zeitschrift) / Print
-
Titel:Additive manufacturing in unmanned aerial vehicles (UAVs): Challenges and potential
-
Beteiligte:
-
Erschienen in:Aerospace science and technology ; 63 ; 140-151
-
Verlag:
- Neue Suche nach: Elsevier
-
Erscheinungsort:Paris
-
Erscheinungsdatum:2017
-
ISSN:
-
ZDBID:
-
DOI:
-
Medientyp:Aufsatz (Zeitschrift)
-
Format:Print
-
Sprache:Englisch
- Neue Suche nach: 55.50 / 55.60
- Weitere Informationen zu Basisklassifikation
-
Schlagwörter:
-
Klassifikation:
-
Datenquelle:
Inhaltsverzeichnis – Band 63
Zeige alle Jahrgänge und Ausgaben
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- 1
-
Formation of near-Chapman–Jouguet oblique detonation wave over a dual-angle rampBhattrai, Sudip et al. | 2017
- 9
-
Form-finding design of cable-mesh reflector antennas with minimal length configurationYang, Guigeng et al. | 2017
- 18
-
Optimum active twist input scenario for performance improvement and vibration reduction of a helicopter rotorYou, Younghyun et al. | 2017
- 33
-
Numerical investigation of a HPT with different rotor tip configurations in terms of pressure ratio and efficiencyda Silva, Lucilene Moraes et al. | 2017
- 41
-
Optimal recursive estimation for networked descriptor systems with packet dropouts, multiplicative noises and correlated noisesWang, Xin et al. | 2017
- 54
-
Iterative update correction and multi-frame state extraction based probability hypothesis density filterZhang, Huanqing et al. | 2017
- 63
-
Design optimization of a three-dimensional diffusing S-duct using a modified SST turbulent modelGan, Wenbiao et al. | 2017
- 73
-
Aerodynamic design of an ultra-low rotating speed geared fanZhang, Jinhuan et al. | 2017
- 82
-
Distributed real-time non-linear receding horizon control methodology for multi-agent consensus problemsSun, Fei et al. | 2017
- 91
-
Individual stress determination in irregularly perforated unsymmetrically-loaded structures from temperature dataSamad, W.A et al. | 2017
- 100
-
Reply “Comment on the paper “Nonlinear radiation effects on squeezing flow of a Casson fluid between parallel disks, Syed Tauseef Mohyud-Din, Sheikh Irfanullah Khan, Aerospace Science and Technology 48 (2016) 186–192”Mohyud-Din, Syed Tauseef et al. | 2017
- 101
-
Active monitoring and vibration control of smart structure aircraft based on FBG sensors and PZT actuatorsGao, Zhiyuan et al. | 2017
- 110
-
Experimental and 3D CFD analysis on optimization of geometrical parameters of parallel vortex tube cyclone separatorRafiee, Seyed Ehsan et al. | 2017
- 123
-
Automated thermal and stress preliminary analyses applied to a turbine rotorMoret, Maxime et al. | 2017
- 132
-
Evaluation of forming forces in ultrasonic incremental sheet metal formingLi, Pengyang et al. | 2017
- 140
-
Additive manufacturing in unmanned aerial vehicles (UAVs): Challenges and potentialGoh, G.D et al. | 2017
- 152
-
A fast multi-objective optimization design method for emergency libration point orbits transfer between the Sun–Earth and the Earth–Moon systemsWang, Wei et al. | 2017
- 167
-
Unsteady aerodynamic and optimal kinematic analysis of a micro flapping wing rotorLi, H et al. | 2017
- 179
-
Three-dimensional compressor blading design improvements in low-speed model testingZhang, Chenkai et al. | 2017
- 191
-
Tether tension control law design during orbital transfer via small-gain theoremLiu, Helong et al. | 2017
- 203
-
Reduced order unsteady aerodynamic model of a rigid aerofoil in gust encountersZhou, Qiang et al. | 2017
- 214
-
Dynamic optimal output feedback control of satellite formation reconfiguration based on an LMI approachWei, Changzhu et al. | 2017
- 232
-
Free vibration analysis of a hard-coating cantilever cylindrical shell with elastic constraintsSun, Wei et al. | 2017
- 245
-
LES study on the shape effect of ground obstacles on wake vortex dissipationWang, C.H. John et al. | 2017
- 259
-
Nonlinear vibrations and stability analysis of a rotor on high-static-low-dynamic-stiffness supports using method of multiple scalesNavazi, H.M et al. | 2017
- 266
-
Online optimal midcourse trajectory modification algorithm for hypersonic vehicle interceptionsZhou, Jin et al. | 2017
- 278
-
An investigation on supersonic bevelled nozzle jetsWu, Jie et al. | 2017
- 294
-
Behaviour of trailing wing(s) in echelon formation due to wing twist and aspect ratioM, Gunasekaran et al. | 2017
- 304
-
Numerical investigation of characteristic frequency excited highly underexpanded jetsLi, Xiaopeng et al. | 2017
- 317
-
Nonlinear control of sway in a tethered satellite system via attitude control of the main satelliteYousefian, Peyman et al. | 2017
- 328
-
Hygrothermal analysis of laminated composite plates in terms of an improved C0-type global–local modelJin, Qilin et al. | 2017
- 344
-
Expected drag minimization for aerodynamic design optimization based on aircraft operational dataLiem, Rhea P et al. | 2017
- 363
-
Nonlinear aeroelastic scaling of high aspect-ratio wingsSpada, Christian et al. | 2017
- 372
-
Influence of the presence of defects on the adhesive layer for the single-lap bonded joint—Part II: Probabilistic assessment of the critical stateElhannani, M et al. | 2017
-
Editorial Board| 2017