Flow and Thermal History Effects on Morphology and Tensile Behavior of Poly(oxymethylene) Micro Injection Molded Parts (Englisch)
- Neue Suche nach: Kamal, M. R.
- Neue Suche nach: El Otmani, R.
- Neue Suche nach: Derdouri, A.
- Neue Suche nach: Chu, J.-S.
- Neue Suche nach: Kamal, M. R.
- Neue Suche nach: El Otmani, R.
- Neue Suche nach: Derdouri, A.
- Neue Suche nach: Chu, J.-S.
In:
International Polymer Processing
;
32
, 5
; 590-605
;
2017
- Aufsatz (Zeitschrift) / Print
-
Titel:Flow and Thermal History Effects on Morphology and Tensile Behavior of Poly(oxymethylene) Micro Injection Molded Parts
-
Beteiligte:Kamal, M. R. ( Autor:in ) / El Otmani, R. ( Autor:in ) / Derdouri, A. ( Autor:in ) / Chu, J.-S. ( Autor:in )
-
Erschienen in:International Polymer Processing ; 32, 5 ; 590-605
-
Verlag:
- Neue Suche nach: De Gruyter
-
Erscheinungsort:Berlin
-
Erscheinungsdatum:2017
-
ISSN:
-
ZDBID:
-
DOI:
-
Medientyp:Aufsatz (Zeitschrift)
-
Format:Print
-
Sprache:Englisch
- Neue Suche nach: 51.70 / 58.22
- Weitere Informationen zu Basisklassifikation
- Neue Suche nach: 020/5755
-
Schlagwörter:
-
Klassifikation:
-
Datenquelle:
Inhaltsverzeichnis – Band 32, Ausgabe 5
Zeige alle Jahrgänge und Ausgaben
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- 525
-
Contents| 2017
- 526
-
Editorial| 2017
- 527
-
Process Induced Defects in Liquid Molding Processes of CompositesHamidi, Y. K. / Altan, M. C. et al. | 2017
- 545
-
Crystallization of Polymers in Processing Conditions: An OverviewHaudin, J.-M. / Boyer, S. A. E. et al. | 2017
- 555
-
Modelling of the Plastisol Knife Over Roll Coating ProcessAbdesselam, Y. / Demay, Y. / Castellani, R. / Agassant, J. F. / Peres, R. / Gourdin, D. et al. | 2017
- 562
-
Low Density Polypropylene/Waste Cellulose Fiber Composites by High-Shear Thermo-Kinetic MixerOguz, O. / Simsek, E. / Bilge, K. / Menceloglu, Y. Z. et al. | 2017
- 568
-
Evaluation of Structures and Morphologies of Recycled PC/PET Blends Fabricated by High-Shear Kneading ProcessingIshigami, A. / Kodama, Y. / Wagatsuma, T. / Ito, H. et al. | 2017
- 574
-
Transient Swell of a High Density Polyethylene Using Adjustable Gap Slit DieKonaganti, V. K. / Behzadfar, E. / Kwak, R. / Mitsoulis, E. / Hatzikiriakos, S. G. et al. | 2017
- 582
-
Effect of Solvent Volatility on Diameter Selection of Bicomponent Nanofibers Produced by Gas Jet Fiber Process TestRajgarhia, S. S. / Jana, S. C. et al. | 2017
- 590
-
Flow and Thermal History Effects on Morphology and Tensile Behavior of Poly(oxymethylene) Micro Injection Molded PartsKamal, M. R. / El Otmani, R. / Derdouri, A. / Chu, J.-S. et al. | 2017
- 606
-
Tailoring Heat-Seal Properties of Biodegradable Polymers through Melt BlendingTabasi, R. Y. / Ajji, A. et al. | 2017
- 614
-
Development of Dispersion during Compounding and Extrusion of Polypropylene/Graphite Nanoplates CompositesRodrigues, P. / Santos, R. M. / Paiva, M. C. / Covas, J. A. et al. | 2017
- 623
-
The Grafting of PE-g-MA Chains on Graphene Derivatives to Improve Tensile Properties of PolyethyleneElhamnia, M. / Motlagh, G. H. / Goudarzi, R. et al. | 2017
- 637
-
High-Pressure Preform Foam Blow MoldingMark, L. H. / Chu, R. K. M. / Wang, G.-L. / Park, C. B. et al. | 2017
- 648
-
Fluid Elasticity in Plastic Pipe Extrusion: Loads on Die BarrelSaengow, C. / Giacomin, A. J. et al. | 2017
- 659
-
Rheological In-Mold Measurements and Characterizations of Sheet-Molding-Compound (SMC) Formulations with Different Constitution Properties by Using a Compressible Shell ModelHohberg, M. / Kärger, L. / Bücheler, D. / Henning, F. et al. | 2017
- 669
-
PPS News| 2017
- 671
-
Seikei-Kakou Abstracts| 2017