Finish machining of mirror-like diamond surfaces using a composite electroplating in-process sharpening method (Englisch)
- Neue Suche nach: Chen, Tai-Jia
- Neue Suche nach: Lee, Rong-Tsong
- Neue Suche nach: Chiou, Yuang-Cherng
- Neue Suche nach: Chen, Tai-Jia
- Neue Suche nach: Lee, Rong-Tsong
- Neue Suche nach: Chiou, Yuang-Cherng
In:
Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
;
227
, 11
;
1596-1606
;
2013
- Aufsatz (Zeitschrift) / Elektronische Ressource
-
Titel:Finish machining of mirror-like diamond surfaces using a composite electroplating in-process sharpening method
-
Beteiligte:
-
Erschienen in:
-
Verlag:
- Neue Suche nach: SAGE Publications
-
Erscheinungsdatum:01.11.2013
-
Format / Umfang:11 pages
-
ISSN:
-
DOI:
-
Medientyp:Aufsatz (Zeitschrift)
-
Format:Elektronische Ressource
-
Sprache:Englisch
-
Schlagwörter:
-
Datenquelle:
Inhaltsverzeichnis – Band 227, Ausgabe 11
Zeige alle Jahrgänge und Ausgaben
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- 1581
-
Assessment of cutting forces in high-speed milling of Inconel 718 considering the dynamic effectsLi, Huaizhong / Wang, Jun et al. | 2013
- 1596
-
Finish machining of mirror-like diamond surfaces using a composite electroplating in-process sharpening methodChen, Tai-Jia / Lee, Rong-Tsong / Chiou, Yuang-Cherng et al. | 2013
- 1607
-
Directional morphological approaches from image processing applied to automatic tool selection in computer numerical control milling machineMejia-Ugalde, Mario / Trejo-Hernandez, Miguel / Dominguez-Gonzalez, Aurelio / Osornio-Rios, Roque A / Benitez-Rangel, Juan P et al. | 2013
- 1620
-
Investigation of the effect of different cutting parameters on chip formation of low-lead brass with experiments and simulationsLaakso, Sampsa VA / Hokka, Mikko / Niemi, Esko / Kuokkala, Veli-Tapani et al. | 2013
- 1635
-
Framework for evaluation of the relative contribution of the process on porosity–cutting force dependence in micromilling of titanium foamsAbolghasemi Fakhri, Mohammadmehdi / Bordatchev, Evgueni V / Tutunea-Fatan, O Remus et al. | 2013
- 1651
-
Micro electrochemical sinking and milling method for generation of micro featuresGhoshal, B / Bhattacharyya, B et al. | 2013
- 1664
-
Modeling of silicon ingot slicing process by wire–electrical discharge machiningDongre, Ganesh G / Vesivkar, Cyrus / Singh, Ramesh / Joshi, Suhas S et al. | 2013
- 1679
-
Neural network–based modeling to predict residual stresses during electric discharge machining of Al/SiC metal matrix compositesSidhu, Sarabjeet Singh / Batish, Ajay / Kumar, Sanjeev et al. | 2013
- 1693
-
Improvement of a deburring tool for intersecting holes with reduced irregular cutting of burr edgeCho, Chang-Hee / Kim, Jung-Hoon / Chae, Soo-Won / Kim, Kwon-Hee et al. | 2013
- 1704
-
Tool wear when tapping operation of compacted graphite ironda Mota, Paulo R / Reis, Alexandre M / Machado, Alisson R / Ezugwu, Emmanuel O / da Silva, Marcio B et al. | 2013
- 1714
-
Laser–material interaction and grooving performance in ultrafast laser ablation of crystalline germanium under ambient conditionsManickam, Sivakumar / Wang, Jun / Huang, Chuanzhen et al. | 2013
- 1724
-
Hybrid-type spatial mask–panel alignment system for manufacturing flat panel displaysKwon, SangJoo / Hwang, Jaewoong et al. | 2013
- 1733
-
A hybrid approach to multi-criteria optimization based on user’s preference ratingCheema, Manjot S / Dvivedi, Akshay / Sharma, Apurbba K et al. | 2013
- 1743
-
Defects of wave patterns from tungsten carbide/stainless steel brazed micro-end-milling for printed circuit board machiningKim, Jin-Woong / Yoon, Hae-Sung / Lee, Hee-Shin / Lee, Kyung-Eun / Ahn, Sung-Hoon et al. | 2013
- 1748
-
An industrially feasible approach to process optimisation of abrasive flow machining and its implementation perspectivesHoward, Mitchell / Cheng, Kai et al. | 2013