Effects of cooling time and alloying elements on the microstructure of the gleeble-simulated heat-affected zone of 22% Cr duplex stainless steels (Englisch)
Nationallizenz
- Neue Suche nach: Hsieh, Rong-Iuan
- Neue Suche nach: Liou, Horng-Yih
- Neue Suche nach: Pan, Yeong-Tsuen
- Neue Suche nach: Hsieh, Rong-Iuan
- Neue Suche nach: Liou, Horng-Yih
- Neue Suche nach: Pan, Yeong-Tsuen
In:
Journal of Materials Engineering and Performance
;
10
, 5
;
526-536
;
2001
- Aufsatz (Zeitschrift) / Elektronische Ressource
-
Titel:Effects of cooling time and alloying elements on the microstructure of the gleeble-simulated heat-affected zone of 22% Cr duplex stainless steels
-
Beteiligte:
-
Erschienen in:Journal of Materials Engineering and Performance ; 10, 5 ; 526-536
-
Verlag:
- Neue Suche nach: Springer-Verlag
-
Erscheinungsort:New York
-
Erscheinungsdatum:01.10.2001
-
Format / Umfang:11 pages
-
ISSN:
-
DOI:
-
Medientyp:Aufsatz (Zeitschrift)
-
Format:Elektronische Ressource
-
Sprache:Englisch
-
Schlagwörter:
-
Datenquelle:
Inhaltsverzeichnis – Band 10, Ausgabe 5
Zeige alle Jahrgänge und Ausgaben
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- 507
-
Effects of surface preparation on pitting resistance, residual stress, and stress corrosion cracking in austenitic stainless steelsRhouma, A. Ben / Sidhom, H. / Braham, C. / Lédion, J. / Fitzpatrick, M. E. et al. | 2001
- 515
-
Microstructural modification in a laser-treated 2.25Cr-1Mo steelSubba Rao, R. V. / Parameswaran, P. / Dayal, R. K. et al. | 2001
- 521
-
The effect of graphite particles addition on the surface finish of machined Al-4 Wt.% Mg alloysHayajneh, Mohammed T. / Hassan, Adel Mahammod / Al-Omari, Mohammad Abdul-Hameed et al. | 2001
- 526
-
Effects of cooling time and alloying elements on the microstructure of the gleeble-simulated heat-affected zone of 22% Cr duplex stainless steelsHsieh, Rong-Iuan / Liou, Horng-Yih / Pan, Yeong-Tsuen et al. | 2001
- 537
-
Improvement of the wear resistance of Ti-based coating sliding against copper alloyKao, W. H. et al. | 2001
- 542
-
Effect of oxide additives and particle size on stabilization of treated commercial zirconiaYasmeen, Maham / Ansar, Syed Asif / Khan, Amir Azam / Joyeux, Thierry / Labbe, Jean Claude et al. | 2001
- 548
-
Low cost corrosion damage mitigation and improved fatigue performance of low plasticity burnished 7075-T6Prevéy, Paul S. / Cammett, John et al. | 2001
- 556
-
Structure-property correlation of two Cu-bearing high-strength low-alloy steelsBini, T. B. / Kanchanamala, D. / Iyer, K. J. L. / Sundaresan, S. / Radhakrishnan, V. M. et al. | 2001
- 567
-
Kinetics of strain aging in bake hardening ultra low carbon steel—a comparison with low carbon steelDe, A. K. / Cooman, B. C. / Vandeputte, S. et al. | 2001
- 576
-
Fracture toughness properties of high-strength martensitic steel within a wide hardness rangeAbd-Allah, N. M. / El-Fadaly, M. S. / Megahed, M. M. / Eleiche, A. M. et al. | 2001
- 586
-
Grinding-induced residual stress estimation by indentation-fracture method in ground silicon nitridesHoshide, Toshihiko / Abe, Junko et al. | 2001
- 592
-
The effect of Mo on the structure of high Cr-Mo alloy ironHuang, X. et al. | 2001
- 596
-
Evaluation of an Al-Zn-Mg-Li alloy/potential candidate as Al-sacrificial anodeValdez, S. / Mena, B. / Juarez-Islas, J. A. / Genesca, J. et al. | 2001
- 602
-
Corrosion behavior of powder metallurgy Y2O3 dispersed iron-and nickel-base superalloysDebata, M. / Upadhyaya, G. S. et al. | 2001
- 608
-
Fireside corrosion of superheater materials in chlorine containing flue gasValente, T. et al. | 2001
- 614
-
Determination of the toughness of in-service steam turbine disks using small punch testingFoulds, J. / Viswanathan, R. et al. | 2001