Further evaluation of anti-veining sand additives (Englisch)
- Neue Suche nach: Showman, R.E.
- Neue Suche nach: Harmon, S.B.
- Neue Suche nach: Showman, R.E.
- Neue Suche nach: Harmon, S.B.
In:
Annual Metalcasting Congress, 116
;
205-211
;
2012
-
ISBN:
- Aufsatz (Konferenz) / Print
-
Titel:Further evaluation of anti-veining sand additives
-
Weitere Titelangaben:Weitere Bewertung von Formstoffzusätzen zur Verhinderung von Blattrippen
-
Beteiligte:Showman, R.E. ( Autor:in ) / Harmon, S.B. ( Autor:in )
-
Erschienen in:Annual Metalcasting Congress, 116 ; 205-211Transactions of the American Foundry Society ; 120 ; 205-211
-
Verlag:
- Neue Suche nach: American Foundry Society (AFS)
-
Erscheinungsort:Schaumburg
-
Erscheinungsdatum:2012
-
Format / Umfang:7 Seiten, 16 Bilder, 5 Quellen
-
ISBN:
-
Medientyp:Aufsatz (Konferenz)
-
Format:Print
-
Sprache:Englisch
-
Schlagwörter:
-
Datenquelle:
Inhaltsverzeichnis Konferenzband
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- 1
-
"Stop Pouring, Start Casting"Campbell, J. et al. | 2012
- 13
-
Systematic optimization of aluminum sand casting gating systemsSturm, J.C. / Dieckhues, G.W. / Sikorski, S. et al. | 2012
- 23
-
Simulation of the entire core production processSchneider, M. / Stevenson, R. et al. | 2012
- 33
-
Management decision making and the cost/benefit of multiple 100 % inspectionsSchorn, T.J. et al. | 2012
- 47
-
Improving the directional solidification of complex geometries through taper additionMonroe, C.A. / Gorsky, D.A. / Huffs, R.K. / Grandhi, R.V. et al. | 2012
- 55
-
Influence of solutionizing time, modification, and cooling rate on the decomposition of Mg-containing iron intermetallic phase in 357 alloysElsharkawi, E.A. / Samuel, A.M. / Samuel, F.H. / Simielli, E. / Sigworth, G.K. et al. | 2012
- 67
-
Effects of intermetallics on the fracture behavior of Al-Si-Cu-Mg base alloysIbrahim, M.F. / Samuel, E. / Samuel, A.M. / Al-Ahmari, A.M.A. / Samuel, F.H. et al. | 2012
- 85
-
Assessment of the effect of Mg addition on the solidification behavor of Al-Si-Cu cast alloysMohamed, A.M.A. / Samuel, F.H. / Alkahtani, S. et al. | 2012
- 97
-
Modeling of microstructure and mechanical properties of aluminum alloys during the casting and heat treatment processSchneider, M. / Heisser, C. et al. | 2012
- 107
-
Thermal control of die cooling using inexpensive standard camerasSrsen, D. / Chen, X. / Hu, H. et al. | 2012
- 115
-
Behavior of bubbles under directional solidification conditionsTeng, Y. / Yang, Y. / Yu, H. / Wang, L. / Huang, W. / Han, Q. et al. | 2012
- 125
-
Radical motion of bubles in the Mushy zoneHan, Q. et al. | 2012
- 133
-
In situ manufacturing of nano-particle reinforced metal matrix compositesBorgonovo, C. / Makhlouf, M.M. et al. | 2012
- 139
-
Modeling the response of aluminum alloy castings to precipitation hardening heat treatmentWu, C. / Makhlouf, M.M. et al. | 2012
- 149
-
Hot tearing in cast Al alloys: mechanisms and process controlsLi, S. / Apelian, D. / Sadayappan, K. et al. | 2012
- 157
-
Localized strenghtening of cast Al components via friction stir processingSun, N. / Apelian, D. et al. | 2012
- 165
-
Effects of alloying elements and cutting tool materials on the machinability of Al-Si cast alloysGarza-Elizondo, G.H. / Samuel, E. / Mohamed, A.M.A. / Samuel, A.M. / Samuel, F.H. et al. | 2012
- 179
-
Nano-refinement of eutectic and primary silicon fibers in Al-Si alloys for high strength structural applicationsShamsuzzoha, M. / Nastac, L. / Berry, J.T. et al. | 2012
- 187
-
Antimicrobial copper: Clinical performance against bacteria that cause infections and impact of their use on hospital patientsMichel, J.H. / Michels, H.T. / Moran, W.R. / Estelle, A.A. / Sexton, K.E. / Schmidt, M.G. / Attaway, H.H. et al. | 2012
- 195
-
High efficiency cold box processes - Technology focused on business goalsArchibald, J. / Kroker, J. et al. | 2012
- 205
-
Further evaluation of anti-veining sand additivesShowman, R.E. / Harmon, S.B. et al. | 2012
- 213
-
Replacement of olivine with silica sand in non-ferrous foundriesLaFay, V.S. / Neltner, S.L. / Ziegler, M. / Thiel, J. et al. | 2012
- 229
-
Measurement and confirmation of thermal properties of investment ceramic shell by multiple methodsXu, M. / Lekakh, S.N. / Mahimkar, C. / Richards, V.L. / Dutler, S.A. et al. | 2012
- 237
-
Foam pattern aging and its effect on crack formation in investment casting ceramic shellsEverhart, W.A. / Lekakh, S.N. / Richards, V.L. / Smith, J.D. / Li, H. / Chandrashekhara, K. / Zhao, H. / Nam, P.S. et al. | 2012
- 245
-
Preliminary investigation on the effect of binder content and ratio on heat transferGiese, S.R. / Ravi, S. / Boss, K. / Biersner, B. et al. | 2012
- 253
-
An experimental methodology based on solidification curves for controlling the manufacture of compacted graphite ironsLoizaga, A. / Larranaga, P. / Asenjo, I. / Sertucha, J. / Suarez, R. et al. | 2012
- 263
-
Microstructure, composition and impact strength variations measured in a hevy section as-cast ferritic ductile iron castingGrenier, S. / Labrecque, C. et al. | 2012
- 277
-
Microalloying in Austempered Ductile Iron (ADI)Padan, D.S. et al. | 2012
- 289
-
The optimal alloy designing and process conditions for heavy section ductile cast irons with high sub-zero impact toughnessPan, E.N. / Lin, C.C. / Chang, R.M. et al. | 2012
- 297
-
Investigation of cast iron processing to produce controlled dual graphite structure in castingsLekakh, S.N. / Qing, J. / Richards, V.L. et al. | 2012
- 307
-
Aging and machinability interactions in cast ironLekakh, S.N. / Richards, V.L. et al. | 2012
- 319
-
Effect of Si segregation on low temperature toughness of ductile ironLekakh, S.N. / Richards, V.L. / Medvedeva, N. et al. | 2012
- 329
-
Gray cast iron with high austenite-to-eutectic ratio. Part I - Calculation and experimental evaluation of the fraction of primary austenite in cast ironAlonso, G. / Larranaga, P. / Sertucha, J. / Suarez, R. et al. | 2012
- 337
-
Gray cast iron with high austenite-to-eutectic ratio. Part II - Increasing the austenite-to-eutectic ratio through austenite nucleationLarranaga, P. / Sertucha, J. / Loizaga, A. / Suarez, R. / Stefanescu, D.M. et al. | 2012
- 347
-
Gray cast iron with high austenite-to-eutectic ratio. Part III - High strength, low hardness, high carbon equivalent gray iron with superfine graphiteLarranaga, P. / Sertucha, J. / Loizaga, A. / Suarez, R. / Stefanescu, D.M. et al. | 2012
- 355
-
The effect of nodularity and surface condition on the fatigue properties of CG ironBoonmee, S. / Stefanescu, D.M. et al. | 2012
- 365
-
The use of combined liquid displacement and cooling curve analysis in understanding the solidification of cast ironStefanescu, D.M. / Moran, M. / Boonmee, S. / Guesser, W.L. et al. | 2012
- 375
-
Simultaneous cooling and contraction / expansion curve analysis during ductile iron solidificationChisamera, M. / Riposan, I. / Stan, S. / Barstow, M. et al. | 2012
- 389
-
Avoiding shrinkage defects and maximizing yield in ductile ironWhite, D. et al. | 2012
- 399
-
Comparison of monotonic and cyclic properties of ductile irons in the AFS/DOE strain-life fatigue database for cast ironTartaglia, J. et al. | 2012
- 415
-
Hot tearing in magnesium AZ91E bell housings produced by the low pressure permanent mold processChiesa, F. / Giguere, N. / Duchesne, B. / Baril, J. et al. | 2012
- 423
-
Recycling and degassing of AZ91E magnesium alloy castings and its effects on mechanical properties and microstructureElsayed, A. / Lun Sin, S. / Vandersluis, E. / Hill, J. / Ahmad, S. / Ravindran, C. et al. | 2012
- 431
-
Microstructure evolution of cast Mg AZ31B alloy at low superheatNastac, L. / El-Kaddah, N. et al. | 2012
- 441
-
Effect of Ni on fluidity of Cr-Mo steelsDash, A. / Lekakh, S.N. / Van Aken, D.C. et al. | 2012
- 449
-
Increasing melting energy efficiency in steel foundriesBiswas, S. / Peaslee, K.D. / Lekakh, S. et al. | 2012
- 457
-
On the crystallography of peritectic austenite and the role of primary ferrite in high manganese and aluminum steelsMcGrath, M.C. / Van Aken, D.C. et al. | 2012
- 469
-
Dynamic fracture toughness of high strength cast steelsBartlett, L.N. / Dash, A. / Van Aken, D.C. / Richards, V.L. / Peaslee, K.D. et al. | 2012
- 487
-
Experiences in casting FeMnAlTuttle, R.B. et al. | 2012
- 497
-
The effects of silicon on mechanical properties and inclusion content of a 0.3 wt% plain carbon steelGittings, J.D. / Tuttle, R.B. et al. | 2012
- 507
-
Effect of chemical composition on the carbide reprecipitation kinetics of Hadfield austenitic manganese steelFuoco, R. / Todorov, D. / Cavalcanti, A.H. / Santos, N.L. et al. | 2012