Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements (Englisch)
Nationallizenz
- Neue Suche nach: Woźniak, Ryszard
- Neue Suche nach: Taryma, Stanislaw
- Neue Suche nach: Ronowski, Grzegorz
In:
Key Engineering Materials
;
490
;
179-186
;
2011
- Aufsatz (Zeitschrift) / Elektronische Ressource
-
Titel:Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements
-
Beteiligte:
-
Erschienen in:Key Engineering Materials ; 490 ; 179-186
-
Verlag:
- Neue Suche nach: Trans Tech Publications
-
Erscheinungsort:Stafa-Zurich, Switzerland
-
Erscheinungsdatum:21.09.2011
-
Format / Umfang:8 pages
-
ISSN:
-
DOI:
-
Medientyp:Aufsatz (Zeitschrift)
-
Format:Elektronische Ressource
-
Sprache:Englisch
-
Schlagwörter:
-
Datenquelle:
Inhaltsverzeichnis – Band 490
Zeige alle Jahrgänge und Ausgaben
Die Inhaltsverzeichnisse werden automatisch erzeugt und basieren auf den im Index des TIB-Portals verfügbaren Einzelnachweisen der enthaltenen Beiträge. Die Anzeige der Inhaltsverzeichnisse kann daher unvollständig oder lückenhaft sein.
- -1
-
Preface| 2012
- 1
-
A General Approach to the Equalisation of Partial Contact Ratios in 3K Transmissions| 2011
- 8
-
A New Technique of Spine Disease Treatment Supported by ADRSK1 Device| 2011
- 16
-
An Analysis of Weld Damage in Punching Press| 2011
- 25
-
Measurement of Normal Force in Magnetorheological and Ferrofluid Lubricated Bearings| 2011
- 33
-
Compensation of Pressure Peaks in PWK-Type Hydraulic Pumps| 2011
- 45
-
Construction Analysis of Mini-Generator of Electric Energy Using Working Medium Flow as the Working Environment| 2011
- 54
-
Crack Propagation in Zirconia MgO-PSZ Ceramic Material| 2011
- 64
-
Designing a Pumping System of Gear Pumps Featuring the Involute Internal Gearing| 2011
- 76
-
Designing of High-Speed Machine Shafts of Carbon Composites with Highly Nonlinear Characteristics| 2011
- 83
-
Development of Bevel Gear Motion Transmission Graphs with FEM| 2011
- 90
-
Dynamics Conscious Approach to Tribometer Design and Tribo-Testing| 2011
- 97
-
Experimental Investigation of Prototype Water-Lubricated Compliant Foil Bearings| 2011
- 106
-
Influence of Design of Hydraulic Components on their Operation in Low Ambient Temperatures| 2011
- 119
-
Influence of Magnetorheological Fluid Volume onto Obtained Critical Pressures on Rotary Shaft Seals| 2011
- 128
-
Influence of Shaft Misalignment on Water Lubricated Turbine Sliding Bearings with Various Bush Modules of Elasticity| 2011
- 135
-
The Influence of the KHß Factor Determination Method on the Evaluation of the Gear Tooth Surface Durability and Bending Strength| 2011
- 135
-
The Influence of the K~H~s~s Factor Determination Method on the Evaluation of the Gear Tooth Surface Durability and Bending StrengthKrawiec, S. et al. | 2012
- 143
-
Investigation of Dynamic Magnetic Fluid Seal Wear Process in Utility Water Environment| 2011
- 156
-
Methods of Increasing Loadability for the Plastic Cycloidal Gears| 2011
- 166
-
Modelling the Contact between the Rolling Elements and the Raceways of Bulky Slewing Bearings| 2011
- 179
-
Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements| 2011
- 187
-
Multicaterpillar Track Chassis of Big Machines - Identification of Loads| 2011
- 195
-
New Satellite Pumps| 2011
- 206
-
Novel Design of an Ocean Wave Power Device| 2011
- 216
-
Numerical Analysis of Crack Propagation in Silicon Nitride| 2011
- 226
-
Numerical and Experimental Analysis of Stress and Strains in Flat Ends of High-Pressure Vessels| 2011
- 237
-
Numerical Model of Bevel Gears Cutting by Duplex Helical Method| 2011
- 247
-
Problems of Analytical Determination of Journal Bearing Bush Fatigue Strength Estimates| 2011
- 257
-
Radial Stiffness of Thrust Ball Bearings| 2011
- 265
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force| 2011
- 273
-
Selected Properties of Bearings with Helical Groove on the Journal| 2011
- 282
-
The Influence of Gas Mixture in the Glow-Discharge Nitriding Process of Austenitic Stainless Steel on Characteristic of Nitrided Cases| 2011
- 288
-
The Influence of Geometrical Parameters on the Friction Process in the Needle Bearing| 2011
- 296
-
The Integrity Analysis of the Structural Element Made of Ultra High Strength Steel| 2011
- 305
-
The Method of Finite Differences in Solutions Concerning Circular Plate| 2011
- 312
-
The Numerical Methods in Geometric Construction Mapping| 2011
- 323
-
Wear of Ultra-Thin DLC or Tungsten-Modified DLC Coatings under Reciprocating Sliding| 2011